25667 LG Washer Dryer Combo - Instructions

1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable supplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.

Did the repair Myself. Saved $ 400.00 in the process.

I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.

Disconnect machine from power source. Then, disconnect any tubes from the back side (make sure you close any water valves before doing so). Then, lay the machine on its back to access the bottom of the machine. Then, locate the thermistor and replace it with the new one (the thermistor will have two screws holding it in place, simply remove the screws and replace the thermistor, then screw it back in). After the new part is installed, stand the machine back up and make sure to connect any tubing to its proper place. Done.

After getting the model info from the back of the washer control panel, I searched Partselect for the water valve part. Easy process, It was here in 2 days. Unplug the machine, I took 2 screws out of the back of the control console and tipped it forward to reveal the valve assy. Turn off the water at the wall and disconnect the hot and cold lines from the washer . I removed the 3 screws holding the valve assy to the deck and with pliers disconnected the 2 clamped rubber lines and then with just finger pressure wiggled the valve from the remaining pipe connections. I swapped the 5 wire connectors to the new valve and wiggled it back into place. Clamped the 2 rubber lines again. and then connected the water inlet hoses to the new valve. Closed it up and called the laundry lady ( sorry honey) 30 minutes to Household harmony again!!

The problem was the valve suppling water to the bleach dispenser was not closing completely. This also caused some water leaking towards
the front of the washer. Replacing the entire valve assembly was very
easy. Unplug the washer, turn off the water, remove the 2 screws that attach the control panel, disconnect the water supplies, unplug the 5 solenoids, remove the hose clamps from the 2 hoses, remove the 3
screws that attach the valve assembly and remove it. Reassemble in reverse order, I did find that applying some water based personal lubricant to the 3 high pressure seals made assembly much easier.

Replaced valve body, very easy to fix as per the video, runs normal.

Our Samsung HE washer started making a grinding noise and stopping at the end of the rinse/spin cycle. I had replaced the clutch and seal 2 years ago and it sounded like it was going out again, however we were not getting the gunk inside the tub like before (seal) and the machine was throwing the tE error code when it stopped which it did not do last time. According to the manual this meant a thermistor error and the solution was "Call for Service". The machine is 9 years old and way out of warranty so....uh No! I ordered the new thermistor for $15 plus shipping to correct the tE code before looking to replace the clutch again or get a new machine. The new thermistor arrived, leaned the machine on its back, unplug one connector, remove two screws and pull the old one out of it's hole, push the new one in, replace two screws and the connector and GO! Problem fixed! No tE code, no stopping, no grinding noise. As best I can tell, the old thermistor was faulting during the spin cycle and the machine went into emergency stop mode which made the grinding noise. It was not the clutch or bearing at all. Most of the repair time was moving the machine out and disconnecting lines so I could lean it onto its back. Note: If your machine is stopping before draining, it will have water inside the tub which will drain out of the hole where the thermistor goes when you pull the old one out. It has an o-ring to seal it, so just expect a little water to come out and be ready to catch all the water or put the new one in quickly.

raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.

Very simple repair after watching YouTube video on how to complete repair.