Models
>
25667
25667 LG Washer Dryer Combo - Overview
Models starting with 25667
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Washer Water Inlet Valve
PartSelect #: PS12374721
Manufacturer #: AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
$126.23
In Stock
Pulsator Cap
PartSelect #: PS3525704
Manufacturer #: 5006EA3009B
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
$30.01
In Stock
Washer Drain Pump Assembly
PartSelect #: PS11706439
Manufacturer #: 5859EA1004P
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
$197.69
In Stock
Tub-to-Pump Hose
PartSelect #: PS3617213
Manufacturer #: AEM73213001
This is a drain hose assembly for top-load models of LG washing machines. This hose specifically is used to allow water to drain from the tub to the drain pump of the washer. This hose is made of plas...
$32.17
In Stock
Switch Assembly,Sensor
PartSelect #: PS3529177
Manufacturer #: 6501EA1001R
This water-level pressure switch in your wash monitors and regulates the water levels throughout the fill, wash, and rinse cycles. You will usually find it inside the control panel or near the tub. It...
$49.27
In Stock
HOSE ASSEMBLY,DRAIN
PartSelect #: PS8749199
Manufacturer #: AEM73732901
This drain hose is a genuine OEM replacement part supplied by LG for use in their washing machines. It is a light gray pipe with a diameter of 1.25 inches. The drain hose is connected to the drain pum...
$36.10
In Stock
Cap,Softener
PartSelect #: PS3534726
Manufacturer #: MBL62061501
This part is the replacement fabric softener cap for your washer. It is also known as the washer dispenser drawer insert. It is made of blue plastic and is approximately 4 1/4 inches by 2 1/4 inches. ...
$21.35
In Stock
SWITCH ASSEMBLY
PartSelect #: PS8751171
Manufacturer #: EBF61674802
This part is the replacement switch assembly for your top-load washer. It contains the switch mechanism and the connecting wire that hooks the door latch to the electrical system of the washer. The li...
$127.02
In Stock
Common Symptoms of models starting with 25667
[Viewing 5 of 5]Leaking
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It did not drain water, cycle stops at rinse+spin.
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su
... Read more
pplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Read less
Parts Used:
-
Jesus from El Paso, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set, Wrench set
16 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
-
Flora from MIAMI, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Wrench (Adjustable)
11 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflow in washer basin
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy
... Read more
. Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.
Read less
Parts Used:
-
Ed from LAKE WORTH, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!