2537481040L Kenmore Refrigerator - Instructions

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice.

This was the second part I tried. The defrost timer was first, but that did not fix it. To do this I had to remove the ice maker and the back plate of the freezer. Then I defrosted the coil and cut the wires. stripped them back and installed the new thermostat. re-assembled and tested. has been working great ever since.

I unplugged the refrigerator, then opened the door and removed four screws holding the plastic electrical panel to the interior top of the main refrigerator compartment and noticed the cold control was corroded badly, apparently from moisture in the panel. I ordered a new one from partselect.com. When it arrived the next day, I then pulled off the control knob, unclipped the cold control, unplugged the three wires to the control, then removed the styrofoam insulation blocks holding the thermocouple wire and then removed the thermocouple wire to complete the removal. I then reversed the process to install the new thermostat and control. That is repositioned the thermocouple wire, put the insulation blocks back to hold the wire, then replugged the three electrical wires, clipped the control back and pushed the control knob back on and finally screwed the panel back to the top of the main compartment and plugged the refrigerator electrical cord back in to provide current to the refrigerator. It immediately started up and ran fine. Total time - about 8 minutes.

This was extremely easy. Took off the control box (housing that covers the light bulb, has the temp control dial on it) and easily replaced the defrost timer. Then, emptied freezer, took off cover at the back of the freezer. Disconnected old defrost thermostat, attached new one, reattached back cover, melted accumulated ice, put stuff back in. Started up. Been running great ever since. No more ice accumulation in freezer. Temp stays constant. Great service from PartSelect, saved lots of money. This job is easy on this fridge, go for it!

pulled broke rack off, snapped new one in place. Yeah!! No more broken jars on the floor.

I just snapped the new shelves in place and !voila! I should've done this years ago.

The gasket pops into a channel could not have been easier.

Ice build up to back of freezer. Fridge way too warm for preserving food/drinks. Unplugged fridge and de-thaw freezer with a hair dryer. Removed and replaced defrost timer in the fridge area which simply unscrews and plugs in. The video supplied by PartSelect worked well for this.

The Defrost Thermostat required a bit more work as it is accessed through the freezer compartment. I had to remove two screws to get the back cover that houses the fan removed. Then you cut the wires from the old Thermostat and remove it before splicing in the new Defrost Thermostat using the supplied crimps and matching the wire colors. It is useful to have a good wire stripper/crimper ready to make the job simple (I bought a pro one for $28 at Home Depot but they can be found cheaper). Also, there is a bit of heat shrink material included to protect the wires from moisture so a heat-gun will do the trick or Good quality electricians tape will also cut it.

I then sparked it up and it works as new. :)

My freezer was frozen but my refrigerated side was not cooling, the temp was actually around 60-degrees. After inspecting i noticed no air was flowing through the vent from freezer side to fridge side. I removed everything from freezer and took the back wall panel off inside freezer section and immedietely noticed alot of ice on coils etc. After researching i found the defrost timer was not working and thus allowing frost and ice to build up on coils and block air flow. My defrost timer was located on the front bottom left behind kick panel, using a phillips screwdriver i removed 2 screws and then disconnected wire harness to the defrost timer. Then i inserted new defrost timer and connected wire harness and then put the 2 screws back in. My fridge is now working great and the ice build-up is gone and i am getting good air flow .. temps on fridge side are now between 32-34degrees. This was an easy project and saved me alot of money doing myself

I had put in a new ice maker and it still had the problem, (I needed the Ice maker anyway) I installed the vale and while I was at it I put a five year filter on the water line that went from the value to the Ice maker, it took less than one hours, the ice is making like it did when it was new, I could not be more please at theis time. Thanks for your Interest. God bless.

The repair didn't require any tools at all. Just simply slide the new glass shelf carefully into the the frame and while holding it horizontally slide the frame back into the rails. This took less than a minute to accomplish. Very satisfied with the results.

Reviewed the video on your website and followed the directions to the letter. Great video

This was a really easy replacement job, but it did not have any directions. The main thing to know is to really "warm" up the new gasket before installing so that it can easily be fit into the door of the refrigerator. Some recommend putting it in warm water, but it's pretty big & I didn't have anything to put it in, so I used a hairdryer to soften it up. It also takes a few days for it to "form" to the door. When I received it, the top right had a seem split, not an actual "rip" but it looked like the glue did not stay to connect the edges very well. I called and Part Select issued a refund and got a new one out to me the next day! Great company!

First, I replaced the defrost timer, really easy, 4 screws popped the cover of the electronic area (top of refrigerator compartment) took it out and plugged in the new time. Unit still would not defrost, so replaced the thermostat as well. Bit harder, removed ice maker, 2 screws, back plate from freezer, 4 screws. Thermostat was clamped to a copper tube- the original had one of the wires hanging out of it- cut the wires and crimped the new wires on, shrunk the plastic tube with blow dryer over the wires (taped them for good measure) and so far so good. Learned most of this through these tips, so keep reading if this isn't your problem, just save myself $1000 on a new refrifgerator...

i removed the 4 screws holding cover. removed two screws holding timer. unplugged timer. plugged in new one. reassembled.