1LE4930XKW0 Whirlpool Dryer - Instructions

I followed your short video and found it very easy to do

Found the belt was broken and the pulley wheel had melted, replaced the belt and the pulley, could not have been simpler. Watched the video on how to repair and in less than 15 mins was fixed. Saved a lot of money by doing it myself.

Turned off circuit breaker to machine. Removed lint trap to allow removal of two Philips screws from vent passage that hold lid on. Opened door and removed two Philips screws that hold switch to front of machine. Using flat blade #2 screw driver pushed on plastic locking tabs under front of machine top about 2" in from either side to allow top to be lifted up from machine. While holding up at 45 degree angle reached in and grabbed switch to pull it out for easy access. Set top down gently once switch was out. While holding switch removed broken switch actuator and installed new actuator on to switch. Lifted top back to 45 degree angle and with left hand held switch assembly in place and started two screws previously removed back into actuator holes. Tightened screws snugly. Lowered top back into plastic locking tabs and gently pushed down to secure top. Installed two screws back to air passage tube for lint trap through two holes in top that were removed at beginning of repair. Install lint trap, turn on circuit breaker and verified operation. Put wet clothes in tub, turned machine on, put away two screw drivers and kissed wife apologizing for taking so long to getting around to repairing machine.

Took 3 screws out used the putty knife to pry the door a part then used the pliers to remove the old door catch and then sapped the new one and put the door back together and I was was done in less than 10 min.

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

Unfortunately after i replaced the new switch the drier worked well. After it stopped for the 2nd time we wanted to put a load and start the swit lost contact. It was not working.It lost the contact with the circuit. No clicking sound the drier not functional. I guess need a new switch?

Removed 2 screws holding the lint trap on top, popped up the top and lifted back, removed 2 screws on the inside top of front panel, lifted front off and set aside then reached under the drum and pulled tension pully to loosen the belt, and removed the drum. popped the motor clams off and then used 2 adjustable wrenches to grasp the nuts at the front and back to remove blower fan. When you look for the area in back to loosen the blower fan you may notice the nut that you are looking for is actually part of the fan and is plastic looking rather than metal. I did have to take off the back cover to the blower fan to tighten it back up.I had seen instructions that the blower fan would have a 3/8 hole in the back of it to loosen it,but mine did not. I assembled it and it works great with my new motor and rollers. I received my part in 2 days, very happy

Removed the drum then removed the old parts and installed the new ones. Dryer now runs very quite and heats good. You have very fast service my mother ordered the parts on the net one day and I received the parts next day and did the repair that night and dried clothes. Thanks,

Your great service is very hard to find.

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

Pop out the old latch and replaced with a new one

just put the new part in the door---sooo easy! THANK YOU!

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.