12500048 Admiral Ice Maker - Instructions

Removed ice maker.

Bottom freezer made access a tad awkward.

New unit did not come with wiring harness, or wire rod that activates cycle, or the front cover, which required transferring those items from old unit. Instructions on internet did not address this.

Installed new unit.

Side by side refrigerators are tough to get two arms inside the freezer side (and do much work) especially to unlatch the power connect. The water tube on this old refrigerator feeds from the back so I took a pair of kitchen shears and made a new opening in the back of the catch basin. Sealed the original opening. Don't know if that was necessary. The video was a big help for this parts change. Much easier than expected. G Keen

Thank you PartSelect. Ordered the replacement icemaker for our Amana refigerator, watched the installation video on PartSelect.com. Followed the instructions, took 15 minutes, works like new. Couldn't have been easier.

I went on line looking for information on Amana Icemakers. Found a number of good sources,how to videos.Using the trouble shooting information I found and the how to videos and Parts Select part search to select the replacement icemaker needed for my Amana that was purchased in 1993.Rolled the frig out changed the leads on the water valve. hit the water dispenser and water went into the ice tray: Water valve good.Did a pre-teardown. Unplug Frig.removed ice bucket. removed three sheet metal screws making it easy to rotate ice maker and unplug the power/control cable. Old ice maker out ready to install new one. New icemaker arrives take ice bucket out, transfer on/off bail from old icemaker to new one attach power cable and in about thirty minutes icemaker is bolted in, fill tube in place and prefill ice tray to start the process. In afew hours we were making ice. pitched the first two harvests.Its working like a champ. Have plenty of ice. Very happy with the whole process.

Removed the chiller level and ice bin exposing the icemaker assembly.
Unplugged the icemaker assembly electrical connecter.
Used the nut driver to remove three screws that fasten the icemaker assembly to the refrigerator side wall and angle bracket.
Removed Ice tray assembly.
Reversed the steps to install the new icemaker.
Cured the problem.

unscrewed the old one! installed the new one! That simple. And I'm female, how easy was that!

took the replacement part and removed to 2 salvageable parts from the leaking tray and installed the 2 on the new tray and then reinstalled the whole unit and we again have ice cubes.

Researched your web site - determined best bet was to replace the ice maker unit. Ordered the new ice maker and believe it it or not it was here in 3 days and installed EXACTLY as it was stated. Frankly it was a snap and was easier than ever expected. Thanks

disconnected electric harness removed screws installed new ice dispensing unit

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the electric plug.
Then I removed the old unit & replaced it with the new, reverseing the proceedure.

It's rather easy and straight foward
(I've done about 3 of them over the years)
take out the ice tray and if you can the top rack (depending on the model of your freezer) for more elbow room. unscrew the bottom screw under- neath the ice maker, then the two top ones, this makes it easier to remove the electrical connector.
take off the old plastic housing(snaps off) put it on new one, take the old wire harness off old, put on the new one, and last take the old wire that turns on the ice maker and shuts it off when full! that pulls out and snaps in the new one, and just reverse the install process!

Turned freez control off. unscrewed singl sheet metal screw, lift off unit, from 2 remain. screws, unplugged
elect connect. Pulled off sm water tube Rmd elect cable unit from old unit, installed on new unit.
Reinstalled elect connect, installed water tube,
Rehung unit on 2 sheet metal screws. Replaced the ice rail[with old one]Turned on freezr control. Had
cubes in 1hr, 4 min... Oh yes, took off old end
decor cover & slipped on new unit .. Greetings from
Hartland, Mi/USA

First I unplugged wiring harness from the inside of the freezer. Then removed two small bolts on top side and one on the bottom. Then took it out of the freezer. Then unplugged the wiring harness from the ice maker. Then plugged it into the new ice maker. Then reinstalled it back into the freezer with the three bolts.Then plugged it back in.

After reading one of the repair stories that applied to my same problem I knew exactly what to do from there. It was simple to remove the old one and install the new one. My ice maker is working great and no more overflowing water.

I found your website with the step by step video on how to replace the ice maker on my refrigerator. It looked really simple, so I ordered the part from you and it was here in 2 days. It absolutely took less than 15 min to remove the old ice maker and replace it with the new one----and it works. You helped me save close to $200.00. Thank you!!!