Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Crossed threaded plastic on old valve was leaking
Removed screws on top of machine to remove the control unit out of the way. Then used large regular screw driver to pry out the two clips that hold the back of the washer tight to the top frame. This allows the back to come away from the machine enough to get the water inlet valve free. Didn't have to remove the bolts at the bottom of the back of the machine (they were pretty rusty) Just removed the single screw holding the water inlet valve in place, slid it down and away from the back cover and could fish it out to the side and disconnect the hose (with plyers) and slide off electrical clips (make a note of which clip goes to which valve.) I removed the part first so I could make sure I was ordering the right one. When the part came (very promptly by the way) it went back together easy. Only question was regarding reinstalling the wires since I didn't mark which way they went. I knew which one went on the Hot and Cold but didn't know if it mattered which clips went on each terminal. Figuring it was AC guessed it didn't matter so put it together the way the connectors seemed to want to lie naturally. Put it together making sure no hoses or wires where pinched or rubbing against sharp edges. Replaced the rubber washers in the hoses and made sure the hose connectors turned freely (they had been rusted a bit and didn't turn on the hose freely and I think this was the start of the cross threading problem) This time the hoses went back on very easily, screwed them hand tight not forcing anything at any time (DIDN"T USE PLIERS!). Tried water and no more leaks. Washer filled faster also, think this was because the screens on the water valve were plugged. I'll have to remember to take the hoses off and make sure the screens are clear every couple years or so. If you are having slow fills, suggest you check this first before tearing in to the machine.
Replaced ring that broke and washer that was bent on the edge.
Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).
Dryer would not start when the start switch was pushed. I was advised by the local repair shop to replace the "push to start switch" and the "thermal fuze". I unplugged the dryer and removed the back dryer casing which took all of 3 minutes. I removed the start switch and thermal fuze using directions on the whirlpool parts forum. This took maybe 5 minutes. I replaced with the new parts and put the casing back on the dryer. The entire project took 15 minutes. The dryer works perfectly. 34 USD for parts and shipping instead of 600 for a new dryer. Easy to identify the parts needed using the model number and the parts arrived the next morning I will use this company again for sure!
After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).
Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go closest to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.
And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.
Installation back into the washer is obvious.
The thing works like a charm! It hasn't worked this well for a decade!
3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.
Once I finally found the part I needed, the repair was very simple and took only a few minutes. Thanks to the very helpful operator to walk me through the diagram to find the corresponding number for the part. I really appreciate your help!
Unplugged the appliance. turned off inlet water and removed hoses. popped the cap off hiding the bolt that keeps the agitator in place and pulled the agitator off. tipped the washer on its front . disconnected the Wire harness. removed the 3 bolts that hold the pump, motor,clutch, (drive assembly in other words). pulled the Drive assembly out of its resting spot removed the bad clutch and replaced it with the new one. then reassembled in reverse order.
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.
Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.
Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors
Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.
If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.
Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks). The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.
First, I wrestled off the top cap of the agitator. Then, I unscrewed the bolt and took out the cam. I noticed that the agitator dogs were worn smooth. I replaced them, put it all back together and VOILA! I bought the whole agitator kit, not knowing what I was going to find, because I wasn't a Magtag repair woman. It ended up that the cam that came in the kit was too big for my washer anyway. Luckily, all I needed was 4 plastic dogs. The price of the whole kit was so inexpensive anyway, it was no big deal. Especially because, I was looking to buy a new washer or a big repair bill. This website is great! Thank you.
First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new hose onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!
After removing the 2 phillips screws at the base of the control panel, I flipped the panel toward the back. Using a screwdriver, I popped off the spring clips, releasing the cabinet. I removed the 1/4" hex head screw on the spring mount and removed the old spring and replaced with the new. I repeated this with the other 2 springs. The spring bracket in the rear also holds the tub balancing spring. It is easily replaced while replacing the suspension spring. If this didn't fix the problem, we were going shopping for a new washer. After this repair, it operates like new!
