11082822101 Kenmore Dryer - Instructions

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

Thank you to the person who commented on the installation of this part.

I purchased a replacement "Thermistor", "Electrode", and "Door Catch Kit" for my 2002 Kenmore Elite He3 electric dryer. I watched several repair video's but wasn't thrilled with the instructions or the high degree of "remove and replace" of components, just to get the the parts I wanted to replace. I took the top panel off my dryer and removed the troubleshooting guide. It showed that the Thermistor, Electrode, and several other components, could be accessed from the front lower panel. I removed the panel, and then the blower cover (two screws and a clip). This gave me access to the Thermistor. It was a little tight, but I removed the part with little problem. Unfortunately the Thermistor the company sent me for my dryer model was incorrect. Not only would it not seat flush in the oblong hole in the blower housing, but the male electrical connectors were a 16th to an 8th inch too wide for the female connectors on the dryer. I ended up cleaning the old Thermistor and re-installed it. We'll see what happens. The Electrode was no problem, I simply removed the lint cover from inside the dryer (3 screws), and carefully pulled the slack in the wire harness enough to remove the electrical connections from the ends of the Electrode. That could have been done without removing the lower panel, but unless you've done it before, I'd recommend removing it, and the blower cover. It gives a better view of the connections. The electrodes have a small metal catch that holds it in the plastic vent cover. You can see it on the replacement part you'll have before you remove the old one. The door catch's are a no brainer. You can look at the new ones and see how that fit. They also come with well written instructions. Good luck with your repairs.

Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you

Using some advice here on this website, and a youtube video found by searching for 'idler pulley replacement' I was able to fix my dryer! Taking off the screws was simple, I used a cordless drill. I have some trouble removing the kick panel, and bent the latches, so there is a small gap between the dryer door panel and the kick panel, but it still works fine. Of note, you DO NOT need to remove the back panel, something I did and cost me some time. I am a bigger guy, so maneuvering on the floor to rig the dryer belt around the new idler pulley "in the dark" was cumbersome, but doable. All in all, an easy enough project for under $30 and less than an hour of my time. Kudos to this website, first, for the super fast shipping, and secondly, the reviewers who posted some instruction. Great job!

Using Partselect to troubleshoot, I determined the heating element was shot. Upon receiving the part, I disassembled the unit, inserted the new element and reconnected everything. It couldn't have been simpler and saved me a ton of money.

Disconnect the dryer from the power source and vent hose. Using the nut driver, remove all hex screws and the electric access panel from back of dryer. Loosen the electrical service cable clamp screws with philips screw driver and disconnect the ground wire. Remove the top panel from the dryer cabinet and the screws that hold the electrical bus in place, then remove the back panel from the dryer. Feed the electrical cable through the cable clamp and rest the back of the dryer against the side. Remove the tri-ring and old idler pulley, then clean and lubricate (WD40) the axel, and install the new pulley and tri-ring. Replace the back panel and all screws.

C/0 both thermostat sensors and fixed dryer Had no heat out ohmed out the coil and it was ok So I ordered both sensors and replaced them and dryer worked great

I followed the instruction for the video I got by email from partselect when I placed the order. 1. Removed front cover at the bottom of the machine. 2. Remove and take out the element base and pull out the element. 3. Install the new element. 4. Test. 5 Close front cover. 5 Run it

I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!

I followed the advice and purchased a thermal fuse in advance. The advice forgot to mention a broken belt switch. Since the belt was broken I had no way of knowing how it was wrapped around the tensioner. Their diagrams are reversed from the Whirlpools. I called a local parts supplier, who turned out to be a repairman working out of his van. I met him in a restaurant parking lot and was on my way in minutes. The dryer was running within a hour. Great web site George - Pittsburgh

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

just the way the video showd me

After shutting off the gas supply and unplugging the electrical cord, I used a flat blade screwdriver to loosen the exhaust vent clamp and remove the vent tube from the outlet. Using a 1/4-inch nut driver I removed the screw holding the plate covering the electrical lead connection to the power supply, then I pulled the plate back and disengaged the tab from the cutout in the back of the dryer body to remove it. I then removed the eight screws holding the back cover of the dryer in place, then removed the cover. The thermal fuse is located near the bottom of the dryer at the back, just above the exhaust vent. I loosened the two screws holding it in place using the 1/4-inch nut driver, then I removed the two electrical leads from the fuse. I inserted the new thermal fuse and screwed it into place, then reinstalled the electrical leads. I then reinstalled the back cover, the power-cord cover, and the vent hose. I turned the gas supply back on and plugged the electrical cord back in.

Used screwdriver to remove outer door trim and broken handle. Reassembled with new part.