Models > 1106907601 > Instructions

1106907601 Kenmore Dryer - Instructions

All Instructions for the 1106907601
361 - 370 of 370
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace lint trap..
New lint trap was in good shape and ready to slide into its proper place. Easily done. Works well.
Parts Used:
Lint Filter with Handle
  • Mark from Mes, AZ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer door would not close and latch on both catches w/o pushing them shut individually.
Our make/model was not on the online instruction, but it was similar. Ours had a glass (plastic)front window in the door. To remove the top catch you had to take out the top four screws that hold the door together (philips head screws) allowing you to pull back the gray plastic strip to access the top latch, then replace it like in the online directions using a needle nose pliers. The bottom catch, once the two remaining the screws were out gives you access to the bottom catch. Remove it with the pliers and snap the new ones into place. You can completely take out the window when you replace the bottom latch if you want.
Parts Used:
Door Catch Kit
  • David from Middleton, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
door wasn't shutting
Just pulled the old parts out on door latch and put the new ones in. Thanks Parts Select for your prompt response and easy process for order and shipment.
Parts Used:
Door Catch Kit
  • Tom from Crystal Lake, IL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The catch on the dryer door had to be replaced
Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.
Parts Used:
Door Catch Kit
  • Vincent A. from Gibsonia, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
My dryer would not work when I closed the door.
I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Michael from Hudson, NH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • John from Sackets Harbor, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
lint filter no handle & wire mesh torn
simple replacement
Parts Used:
Lint Filter with Handle
  • Annie F. from Fresno, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door latch broke
Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you
Parts Used:
Door Catch Kit
  • Leandra from Miami, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Broken safety switch for door
Lifted front top upward, removed two small/long screws holding switch assy. removed two wires, replaced wires on new switch at the N.O and COM tabs, reinstalled switch assy, lowered top down. DU FINI
Parts Used:
Dryer Door Switch Actuator Spring/Lever Door Catch Kit Lid Switch
  • Joseph from West Chester, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
noisy dryer
Repair went fine. Really easy for the most part. Unfortunately it didn't solve my problem. Great place to get parts though. I'm going to continue my search for the source of the noise
Parts Used:
Rear Drum Support Roller Kit
  • Shawn from Brookfield, WI
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 1106907601
361 - 370 of 370
Back to Top