11068087701 Kenmore Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Old lint filter had holes in it.
-
John from Massanutten, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer was throwing a E1 Error
Took the back dryer cover off and removed the lint cover all from the back of the dryer then replaces the Thermistor (held with 2 screws).
Parts Used:
-
John from Indian land, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
My dryer had stop working and the terminal block, wires, and dryer plug burnt out
I replace the terminal block, wires , and dryer plug I unscrewed the back of the dryer and basically replace was burnt out. I was about to pay 200.00 to have it done but I looked on youtube and seen how easy it was so I just chose the site to order what I needed to be replace and it arrived quickly and more affordable to do it myself. Thanks I hope the was useful.
Parts Used:
-
tiffanee from antioch, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
dryer doesn't complete it's cycle
Removal of the back panel was easy - 9 screws - replaced both the thermistor and the two-terminal thermal fuse - put back panel on - supplied power - tested it - works like a champ.
Parts Used:
-
MICHAEL from PHOENIX, AZ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Felt wears on the dryer lint screen
No repair. Just replaced the screens in the dryer and they slide in and out to clean. The felt gets worn fast.
Parts Used:
-
Judy from Cloverdale, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
lint filter coming apart
-
Alan from Oklahoma City, OK
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door Catch broken
Very easy to replace, just removed the door catch and place the new one in and push till clicked. That simply.
Parts Used:
-
Marie from Downers Grove, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Felt on lint filter came off.
-
Mike from Rocky River, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Dryer stopped heating
(Always unplug dryer before making any repairs) I opened the dryer and checked the heating element. Making sure that the connection was good and nothing was damaged, I determined the problem was overheated wires. They melted and lots connection. I replaced them with the heating element wire connection kit. Easy to install and simple to get right. I cleaned the dryer again with a vaccum cleaner, removing all the lint, and checked the vents, making sure they were clear...I turned the breaker on (it was tripped when the dryer overheated)and everything worked great.
Parts Used:
-
Joseph from Austin, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Old filter screen was torn at edge of plastic rim
replaced with new one which had been improved upon by a brace down the middle of the screen.
Parts Used:
-
Dan from Bluffdale, UT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Element went then the high cut off blew
No problem changing the element, but it worked for one load and then the thermostat blew! Bummer but that was another easy fix!
Parts Used:
-
Robert from Grafton, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Broken door catch
Used putty knife to pry broken door catch off .... Snapped in new one. Took maybe two minutes !
Parts Used:
-
James from Ralls, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Door Catch came apart inside the door
The door catch dislodged in the door and apparently broke. The hardest part was getting it out of the door because in trying to remove it, the piece fell into the inside of the door. I could have easily just installed the new part (it snaps right in with great ease, that part took exactly 5 seconds). But hearing that old piece rattle around inside the door would have made me a little nuts. So I decided to take the door apart to retrieve it. It was just a bunch of screws from around the perimeter of the door, but I also had to unhinge it to do the job. Putting the door back together wasn't as easy as I had hoped, with some pretty tight fits and the glass dislodging. Had a few moments where I was regretting. But I got the old part out, snapped the new one right in. I'm sure an appliance guy would have charged me $60 - 90 just for coming out. Instead I repaired the dryer for the cost of a $3 part. One small lesson learned here -- dryer doors are much like refrigerator doors, or at least mine is. There is a door catch on both sides of the door so you can hinge it to open either way. I could have done the repair for nothing! But I love parts select for just this reason. I don't do major repairs, but replacing pieces on appliances couldn't be easier with this service!
Parts Used:
-
Adam from Falls Church, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer would not heat
Removed the front cover of the dryer as well as the lint holder and framework to gain access to the thermal fuse which is behind it and mounted on the discharge side of lint fan. replaced fuse but the dryer still wouldn't heat each time the ignitor glowed. Also then replaced the solenoid (both of them) and this fixd the problem as it has been good for a week now. The solenoid issue is not easy to conclusively identify as an issue as it is inconsistent in operation.
Parts Used:
-
mike from new egypt, NJ
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lint Screen Deteriorated
-
Robert from Ingram, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!