Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer not heating
After removing the back (five nut screws), lifting the top (two lint filter screws), I diagnosed the problem (timer, fuse and sensors tested OK - heating element broken). I uninstalled the heating element cage sensors (three nut screws) but did not unwire them. Then I removed the heating element cage (one nut screw on top and lift) - the right angle screwdriver was very helpful. I removed the broken element (one nut screw on bottom). Ordered from Parts Select online because they had the element for a better price & quicker expedited shipping than Sears. As soon as the part arrived (two days!), I rewired and installed the element and assembled the dryer in the reverse order of the above process. Total time from package arrival to drying clothes (BIG stack) - 30 minutes!
just like the guy in the video. It was easy to folow his instructions, and the best thing of all i could stop the video if I had a question and then resume!
electric dryer stopped heating - the thermostat got very hot
The numbers on the metal plates were the JC Penney numbers - that no one recognizes. I eventually found the model number inside the timer case on a printed schematic. I started by disassembling whatever metal covers were removable by finding sheet metal screws and unscrewing them. If you pull on the sheet metal covers, you can find where they are connected to the frame. Eventually, I found that both the heating element was broken and the thermostat was fried. It took a while looking at various websites to find the proper parts. It's all OK now.
The original lint filter was broken, as the dryer was very old I did have the part #, I searched the internet I saw partselect.com on the search engin I did know it would be so easy to get this product, I selected the part by size specification.
Thank you partselect .com for making my life easy. Or else imagine me driving around looking for stores which sell spares for old dryers wasting time and gas-go green shop at home.
It went well, I followed the instruction video and referred back to it if any questions or difficulty. The instructor on the video was obviously very experienced and duplicating his actions exactly was very helpful, One thing I noticed that wasn't mentioned was that the thread on the wheel / motor is left handed.
found a video online and followed the instructions. First unplug dryer, then take off back cover with a 1/4 inch socket unscrew the 5 screws from the cover and remove back. Then with a ohms meter you have to check to see what terminals are bad. In my case it was the heating element. So, next you go to top of dryer and unscrew the lint trap so you can lift the top of dryer and remove the bracket holding the housing where the element is located. First take off the leads that are connected to the element and housing unit. Then gently lift housing unit up off the hinges and pull it out. Then turn over and there is another screw that holds the heating element in. After unscrewed the element pulls right out and then just put new element in and reverse everything.
I follow the instructions from the video you guys show the only issue is putting back the tensioner in place but my brother leaves next door and help me.
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Heating element was toast
Undid the back, remove wires going to element, unscrew lint trap, pop the top and undid the nut-screw holding the element housing. pulled out the bad element and did everything in reverse with the new element... unplug it first though because I left that step out.
First unplug appliance, Remove dryer top and front. remove drum and belt. Two clamps hold motor in place. remove them and lint chute housing in rear, exposing the fan. Use vice grips to hold motor shaft behind belt pulley flat spot. Remove fan, it's reverse threads. A large adjustable wrench on plastic fan nut and spray lubricant if very tight. Place new motor next to old and switch wires over, crimp on new 1/8'' connectors. Remember the green ground wire may need an allen wrench. Put back drum,belt, lube the rollers and replace back cover, front, top.
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud banging coming from drum area.
I watched a U Tube video about banging sound from dryer. Once I recognized the problem, lifted the top, removed 2 screws holding the front, removed the drum, and bingo. Saw the worn out drum roller. Ordered the replacement parts from "PartSelect" on line (Great Company). Was in no hurry, so I chose regular mail delivery. 4 days later, got the correct replacement parts, put the dryer back together, and now, the dryer is quieter then when I bought it new, a thousand years ago. I will never again be afraid to tackle an appliance issue. THANK YOU !!!
Had to replace the rear felt seal and the motor. It was no problem to find videos on how to do both of these repairs. Took apart the appliance. When the parts came first replaced the drum rear felt seal and waited for the motor to be delivered. Then replaced the motor as per online instructions. Also went to Home Depot to buy a new flexible dryer tube since the old one had a few holes. It works perfectly again.
Dryer door latch broke and door wouldn’t stay shut.
Jimmied out the latch using two screw drivers to get under the edges. Pushed the new piece in. Voila! Took 2 minutes for what my repair man told me would cost about $200 to fix. Unbelievable!!( I first watched some YouTube videos to get the idea )