11062042100 Kenmore Dryer - Instructions

I watched the video and after that made the repair, it was very easy and the video was a really big help. From start to finish it took me no longer than 10 minutes.

My experience was a positive one. I called the company and read the part number from kitchen aid and the technician on the other line knew exactly what i needed. He gave me the part number and the price and took care of my order. Within 3-5 days i received my part. I am really happy with this company and i will call again when one of my applicances is not working.

self...right part thank you

ILove your service. The part came in 3 days. Best parts service I have ever found. I was told by the dealer it would take 2 weeks to come in.

Thank you for your part service. It saved me about $ 200.00 dollars by Sears not coming out to repair a simple problem.

after watching the instuctional installation video, it real took about 25 to 30 mins to install the new belt. The video was perfact and made the installation so easy..

I followed the video for this part. Opened the front panel. Unscrewed the brace on the bottom. Turned the element housing and pulled out after disconnecting the wire leads. Unscrewed the original parts. Screwed in the new parts. Reversed the sequence and ran a load of towels. It was easy and fixed the problem.

I studied the instruction on the partselect.com site, followed the directions to discover the problem, ordered the part from them, installed it as in instructed in their video, and it has worked perfectly for the past 5 days after doing a mountain of laundry. I took the opportunity to clean my dryer interior from all lint and dust as well as the vent. I suspect lint is what caused the problem after I washed some new flannel sheets which clogged my vent cover outside. I cannot say enough good things about the partselect videos. I'm ready to tackle a few other appliances. One note about the Kenmore Elite Dryer 110 model: Do not take the back off. I removed the screws which caused the steel plate to drop a little at the back of the dryer. Then I could not put the screws back in. To fix this, I removed the screws from the control panel and pushed it forward to reach just inside the top back of the dryer...pulled up the steel plate and got the screws to line up and put it all back together. The only other tricky part was getting the heater unit back in to the slot at the back of the dryer. I finally used a little brute force to push it in far enough, then turned it a quarter clockwise to the correct position. My husband was impressed that I tackled this project by myself. Hunting season was on in MN. THANK YOU PartSelect.

Took off front bottom panel reached in removed part that was very dusty. Put in new part. Cleaned out lint inside dryer. Works like a charm.

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

open dyer door replace lint filter perfect fit, good price, fast delvery. thank you

removed cover panel an unbolted and replaced and it works watch the video best 100 dollars we ever spent

First I replaced the heating element. That did not fix the problem, so I used an ohm meter to test the thermostat and fuse (thermal cut-off). One of those was bad, so I ordered the thermostat/fuse conbo and put those in. The hardest part was getting the wires to the right places. I labeled them with masking tape and a sharpie, but maybe they are sized so they only fit one place. I didn't check. The actual work of changing out the parts was super easy. I recommend testing those three parts-heating element, thermostat, fuse-with an ohm meter before buying something you don't need. I now have a spare heating element and thermostat. I should be good for another ten years!

Remove wire terminals, & four screws, install new parts. Very simple fix! This is the second time I've used Parts Select to fix my appliances. Very satisfied customer!

First I removed the front kick panel to observe the drum and blower to see that both were running. I watched the element inside the heat can as well, and saw that it wasn't receiving a current (no heat, wasn't glowing). First thing I did was test the element itself by removing it from the heat can, and with a multimeter set to its lowest ohm setting, touched both terminal ends to check for continuity. The MM read 0 so it was fine. I then removed and tested the thermal fuse and the relay on the blower in the same fashion, removing them and checking them for continuity. They were fine also. I then moved on to the thermal limiter and relay on the heat can, and that's where I found a broken current. After installing both parts on the heat can, I observed the element receiving a current and the problem was fixed. I've done several loads since then and it is drying better than ever. Problem solved, for now.