11060072990 Kenmore Dryer - Instructions

same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.

The latch for my Kenmore dryer was only $10 with shipping and just what I
needed. No instructions included, so I googled installation and it was fixed
in less than 3 minutes... YEAH... I am happy!

In a matter of moments the dryer that I had grown to despise was back on my good list! I took a pair of pliers and removed the old parts, then inserted the new catch kit. I only about 5 minutes to do AND I love my dryer again!

Replaced the thermal Cut off

Loosened two screws in back top of drier and pulled forward and up to hinge top of drier and allow access to door switch.Took out broken actuator spring and replaced with new one,snapped lid back in place and put screws back in hinges and job was done.

drilled a 7/16 diameter hole directly in the center of the two mounting holes filed it square big enough so as the spring tip fits thru now the door closes on the spring which actuates the switch looks and works perfect.

take the old latch out and pop the new one in. Your repair kit worked perfect.

I removed the plastic latch using a screw driver to pry it out. I had to use pliers to completely remove it. Then I snapped the new piece in. It worked perfectly the first time. Very easy repair.

Super easy repair. Funny to think I almost called to have it serviced before I found the Door Catch Kit. The original catch had actually fell into the door so when I got the new part it simply snapped in no tools needed!

removed the broken part and replaced with the new one

This is actually a lesson. The reason the dryer was heating initially was a broken coil in the heating element - I replaced that and the high temp switch that attached the the heating element - replaced the service panel, re-connected the vent line, plugged the dryer back into the wall socket started it up it got hot I was happy little pat on the back. I picked my tools and the wife started working on washing laundry again. However the first load would get dry. I unplugged the dryer from the wall, removed teh vent line, removed the service panel tested my wire connects - checked continuity across the Thermal cut out (which was good during my initial troubleshooting) and it showed open. So once again I was hauling clothes to the laundry mat until the part came in. The lesson is I thought a could save a few bucks and not replace that switch - if the heating element goes out just order both switches with the element and save your self time - replace the switches while you have the dryer apart.

First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.

The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.

*** Unplug machine ****

To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).

Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!

Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.

looked in the manual, it said if there was no heat but the dryer ran, it could be one of the 2 fuses. Found your site online and read some other people's stories. Ordered the thermal cut-off kit on a Sunday night and it was delivered on the following Tuesday night in a bad storm(fast). It took very little time and effort to replace them, and the dryer (22 yrs old) now works better than it has for a long time. This plan worked way better than I could have imagined.

Removed toe plate, make sure and use something like a 5 in 1 painters tool, makes the job easier as you will see a notch inside the seam between toe plate and outer shell, take 1 screw from heater tube cover I used a nut driver, this job is best to use with a stubby socket set, there are 2 machine screws with hex heads holding the heating element to the heating tube, you cant really see the heads but can feel them with your fingers, disconnect the 2 terminals in front of this, but make sure you use a blue or black sharpie to mark the terminals, use your stubby and remove screws, then use a set of needle nose pliers and pull out the heating element, the new heating element slide right in the grooves then reverse the take off process, good luck