Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dryer stopped working
The Door Swith Acuator Spring was broken. I unplugged the dryer. Removed the two screws on the top control panel. Lifted the top of the dryer and propped it up. Then removed the two wires attached to the door switch (remember to label them with tape-one without and one with tape). Then as suggested by a previous "repairman" loosen the two screws that hold the switch just enough to remove the actuator. You do not have to completely remove the screws. Slip in the new actuator and reverse the process. Voila ... you have a new dryer and a very happy better half. I was given a kitchen pass to play golf and savor some "spirit" water.
Advice: Don't slam the dryer door. The actuator will last longer.
First I popped open the top of the dryer so I could see the part. I removed two screws from inside the door that hold the spring lever and switch together. I removed the spring lever which is also like a bracket that holds the switch in place. Put the spring lever back in place over the switch and reinserted the two screws. Done in about 10 minutes.
Dryer would not turn on, found metal clip in laundry
The dryer door has a switch hidden inside the machine housing. The switch has a lever that protrudes and when the door it closed it hits this lever allowing the dryer to activate.
*** Unplug machine ****
To replace: pulled out the lint trap, remove 2 screws under the lint trap. Pry the top open at the front (it's press fit in place and will pry open with a flat screwdriver).
Lift lid up and prop open (like the hood of a car). Find the switch at the front of the machine just above the drum. Remove 2 screws holding the switch in place (from just inside the drum area). Pull off the broken clip bracket, replace with new one and screw it back into place. Be careful not to drop the screws or bracket or they will fall into the bottom and you may never see them again. I can't stress this enough!!
Let the lid down and give it a good rap on the front to seat it back into place, replace the 2 screws under the lint trap. Replace the lint trap. And your done.
the door switch broke, and I had to pop the lid unscrew the switch and use a clothespin to depress the switch acuator button....not pretty.
same as I described above. However i was amazed when the part showed up the very next day...I was expecting maybe 3 or so days later. I wiil absolutely use PartSelect in the future.
I first noticed that the tab of the door switch snapped off so the safety on/off switch did not work when the door was closed. I temporarily taped the switch closed so I could use the dryer. I found the model number from the unit and easily found the schematic and part description from the website. I placed the order and had the part in a few days. Problem solved. Thank you
Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!
The spring lever broke at the bend after 26 years of use.
I followed the basic steps in the video for the dryer door switch replacement. My dryer is much older but everything in the video was basically the same. It was a very easy repair. I have kept this dryer running for 26 of the 27 years of our marriage.
The small end of the actuator switch that the door pushes against was broken off.
I'm a 66 year old lady with no repair experience at all!! I found the part I needed on Parts Select, which I ordered and received in less than 4 days. I watched the video that you've posted on your website which shows in great detail how to do this repair. It looked like a simple fix and it was!! I highly reccomend Parts Select!! Took my granddaughter(held flashlight) and myself less than 30 minutes to do the repair!!!
Located broken front door safety switch actuator. Ordered new part shown on the diagram. Removed broken part, installed new part, start dryer,runs fine.
I thought it might be a damaged switch but when I removed it I noticed a metal clip that was attached to it was broken. The pin on the door pushes against this clip when the door is closed which in turn opens the circuit on the switch. I looked up the model on this website and viewed the parts diagram. There I saw the part I needed and it was listed below along with the cost. Couldn't of been easier. Thanks!
I noticed that the dryer door switch actuator spring/lever was broken on the door. I researched how to get the top of the dryer cover off, and I took apart the mechanism. I called a local repair shop and they wanted me to buy the whole unit instead of just the switch lever. So I did some research to find the part on the web, and I came across your site. It was very easy to navigate, and I fould the part easily. I saved about 66% by just ordering the lever and not the whole unit. I would without hesitation, buy parts from your website again. The part was shipped and received very quickly. Thanks again!
