Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Bellow had a large hole in it, and was letting water drain out all over the floor.
It was a little difficult to put the new Bellow in place on the tub, due to the fact you have to basically push the outside of the Bellow all the way into the tub so you can install the tub clamp. The other difficult part of the task was tightening up the clamp it's self. There really isn't a lot of room to move your hand around in the space you are given to work. But after a few hand cramps and a few things said, that are not needing repeated, I was able to get the clamp tight. Once you have the clamp on the tub, it's basically pretty simple to slide everything else into place. The wire/spring clamp that is used to attach the Bellow to the front of the washer is fairly simple to put into place with a little patience. All in all it was a cheep and easy repair for a due-it-your self repair.
Whirlpool Front loader washining machine F21 error code
Unplugged washer first! Removed front bottom panel by removing three screws, unscrewed the Drain Plug assembly by turning drain plug counter clockwise with a bucket to catch excess water from washer. Used pliers to remove spring clamps from washer agitator drain hose and then removed the spring clamp from the hose going to drain. Checked hoses for obstructions, then Slide Drain Pump assembly up to the right to remove. Then installed new Drain Pump assembly by sliding pump into slot to the left. Connected the agitator and drain hose to new Drain Pump and fastened with spring clamps. Plugged in AC line cord and turned washer on and started a quick wash cycle to check for leaks and to see if the water drained from washer properly. The water drained from washer and error code did not appear. The error code F21 reappeared during the second wash cycle. After closer inspection with a flash light, I found a large piece of cloth caught between the washer agitator and washer tub covering the drain by shining the flash light up towards the Agitator tub. This was solved by removing the Drain Pump assembly and all of the drain hoses again. Then removing the the large hose from the agitator tub and then removing the large piece of cloth from agitator tub. After reassembly, the washer worked like new!
This part worked great! Completely fixed all the problems that I had with my washer. A bit hard to actually place it in(pliers are necessary) but otherwise very easy to install.
Read the instructions provided by PartSelect.....and with a bit of patience I installed all four bolts so the washer's inside agitator was not damaged in shipping. I highly recommend that anyone who is moving/storing or shipping their washer that you find the correct shipping bolts according to your model and make and install them prior to moving your appliance.
Found it impossible to get the bellow off the machine. Removed the front spring. Even tried to but off the bellow. No luck. Called repairman. He had to take off the front panel, door panel, and the top of the machine before he could remove the back spring/clamps.
Pump noise Rattle and not draining water out/ error code
Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !
pulled the front and top of the machine off, pulled off the old bellow, ordered the new bellow, and put the new bellow on. we looked on youtube.com for a video on repairing the machine.
We hired a local repairman and he even had trouble . I would not suggest anyone trying this installation on their own. It took the repair guy an hour to do and he struggled. Not an eary installation