Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Bellows between door and tub
Remove top and front Care taken to unplug door wiring should have taken notes or photos where srews go and order remove old bellows large hose clamp and sping tensioned clip clean surfaces install new bellows on tub only put all panels and door together Connecting wiring to door and strain relief takes 2 people connect bellows to door with spring clip
The inlet valve begins to restrict water flow into the washer based on normal calcium buildup. At a certain point, the washer will start giving an F20 error code indicating it is not getting enough water.
This is a straightforward replacement. Move the washer to an area where you can work on it. Unplug the washer from the wall. Turn off the water and disconnect the hot and cold water hoses at the washer. Remove the back of the washer. Slide out the top of the washer. Remove the small hose from the valve to the remainder of the washer. Disconnect the two control wires to the valve. Replace the valve. Replace the small water hose. Reconnect the wires. Replace the top and back of the washer. Connect the water back up. Plug in and try a test load. The water should flow fast enough to reach the back of the machine.
firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.
The washing machine was not draining. It was showing a code on the washer of 02.
We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.
Washing machine wouldn't run. Kept making buzzing sound and didn't show door latched.
Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.
Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.
Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good
1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.
Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together
One of my baffles just came off during a wash, one of the plastic clps that hold it in place dry rottedafter 10 years
Real easy , the baffle goes in only one way , use the others as guide as too which side the taller end goes. With one hand pushing in the center of the back of the basket , pushing back , simply place and slide baffle towards you with other hand , there will be a crisp snap as it slide in to place.