1103401771 Kenmore Dryer - Instructions

After reading the many different common stories,I replaced both coils (m series).Very simply lifted up the top of driver,held by 2 snap springs and 2 lint vent screws.Removed front cover,2 screws and 2 bottom snaps,coils down on bottom left.r/r both coils,reinstalled covers and let there be heat!This website is a blessing!!

I removed the Drier Door and removed the Front Drier Panel exposing the Gas Valve & associated parts. I removed two (2) screws holding the Gas Valve Coils in place & replaced the 2 terminal coil, then replaced the screws, Front Cover & Drier Door. I liked the results so much, I ordered the other Gas Valve Coil and will replace it also when it arrives.

Good trouble shooting information.

After opening the bottom access panel, I found a lot of lint build up which is very flammable. I took my leaf blower and cleaned it all out. Then I just followed the instructions that came with the part. But be careful as the igniter is fragile. I broke the first one...

took 2 screws out and replace new coils

My gas dryer would run with heat for 5 minutes in all settings, but kick off and not heat again. Timer would not advance in autodry. Thought it was the cycling thermostat, so replaced that, but did not solve the issue. Ordered the coils, and cleaned out heavily clogged lint from bottom of lint trap, especially right above the fan motor at the bottom of the trap. Received the coils, opened the top and front, took out drum, and replaced the coils. The replacement took less than 2 minutes. Be careful putting the drum back on to make sure the felt is not caught inside the drum. You can give it a spin to make sure. Wear gloves, as I cut myself up pretty good on the edges of the dryer body. The inside of my dryer looks like a crime scene! Anyway, I put it back together, and it runs great. Solved the timer advance issue in autodry, and the heat kicks on and off when it is supposed to. Good luck! Thanks Part Select!

Watched youtube video to problem shoot. Cause determined to be coils bad. Searched web found Parts Select to be easiest site to deal with and had coils for best price. Followed instructions supplied with parts. Dryer works like new.

i read some of previous customer problems and fixes pulled the front cover off found coil's location when i turned on drier you could see the ignitor getv hot but burner would not ignite unless i put a little pressure on secondary coil when i let go of coil flame would go out. ordered 'M' series new style coil kit came in in about three days installed parts drier workng good i would reuse parts select agian thanks

Really an easy fix. 2 5/16" screws hold the cover on below the dryer door. From here it's easy access to the gas element. 2 more screws for the valve cover and disconnected the attached wires to the gas coil valves. slip the news ones in place, re-attach the wires and install the holder.Tested the dryer and it fired right up. Put panel back in place and the wife is happy it didn't cost us more than just the parts. Yep, she's a lucky girl. ;0)

As many of the other posts here on this website mentioned, I had the same problem of the dryer not heating up. I removed the front panel (4 screws on each side inside of door - easy - followed instructions) and once off I was able to view the igniter glowing properly so I knew the starter/igniter was not the issue. Everything I read then suggested that it must be the two terminal gas valve coil, and sure enough it was. Ordered part -- got it in literally a couple days -- removed bracket (two screws) put in new coil -- turned it on -- works great. Could not have been easier. This is a great website and would recommend it to everyone who is a Do It Yourselfer.

Remove top then front panel kit goes on gas value 2 screws hold gas tube in place.

I had two dryers, one was gas and the other was electric. The electric stopped heating. So I rolled out the gas dryer, but it was setup for natural gas and at this location, I only have propane. So I changed the jets to work with propane, in the process I broke the igniter, so I replaced that and that made the propane one work. Armed with the knowledge from that job, I took the electric dryer apart located the thermostat and replaced that and low and behold I have two working dryers. One for now and one for an emergency. I only have four screws left over!!!! Jim Cooke

Thanks to reports from others, I concluded that most likely the gas ignition coils (one or both) were no longer functioning properly. I replaced both with the 'M' Series New Style Coil Kit which is about 1/2 the price of either coil individually -- yes,true,go figure! The actual replacement took only about 10 minutes. What was most difficult and took the most time was the removal of the front panel of the cabinet -- this was difficult only because there were no instructions in my owner's manual (or any other source I could find) and it took me awhile to figure it out. Now I could do the whole job in about 20 minutes! The detailed instructions from others as to the process of replacing the coils was invaluable -- I don't know if I would have been able to figure that out on my own. But most important was the information that enabled me to diagnose the problem in the first place. Thank you, all you previous comment contributors.

I first tried replacing the Radiant Flame Sensor, which was located in a tight space and was very difficult to access. I finally gave up and called a handyman to replace it. That didn't fix my problem. I needed a new igniter. That was easy to replace, but it's fragile and I broke the first one...

Well, this is quite easy really. I found the problem after plucking and chucking a few parts but it was finally the igniter that was the problem. After taking the front section panel off to access the components, take the time to unscrew the igniter and see if it is cracked. That is what happened to my unit. I replaced to the new M series coils as well but the issue was the igniter. Look very carefully for a crack, the one on my unit was very small. You can ohm it out with a meter and if it reads open it is cracked.

Dryer was getting hot at start of cycle and would drop out flame and then cycle flame every 45 sec to 1 min. Pulled of panel to observe this and thought it was a heat sensor problem. Went online and people were saying a coil could be bad. I took coils out and tested them and they tested good but I bought new ones anyway as I figured they were going out of range as they heated up, This proved correct as dryer works .