11028522700 Kenmore Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replacing timer unit.
Repair went well. Removed 4 screws holding control panel. Removed multi plug from unit and power plug from unit. Had some difficulty removing control knob however if you look close to timer unit it reads on back of unit that you must hold stem from back of unit and pull knob off. READ INSTRUCTIONS ON BACK OF CONTROL TIMER! OR YOU WILL BREAK THE KNOB OR THE NEW UNIT.
Parts Used:
-
John from Immaculata, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
washer pumped water out but would not spin
took the washing machine out of the washroom closet and did the repair in the kitchen
Parts Used:
-
brian from shohola, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer wont spin
Replaced the clutch - works great. HOWEVER - check the drain pump attached to the motor, there was a small sock clogging it up which also fixed the problem. I saved 600 bucks on not buying a new washing machine!!
Parts Used:
-
jason from prairieville, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
agitator not working correctly
Parts came promptly. Disassemble agitator as per tutorial video on website. Replace locking "dogs" and reassemble. Cheap, effective fix!
Parts Used:
-
Matthew from Bellmore, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
no agitation, no spin, mortor still make noise
take the cabinet frame out first, take the pump off the motor assembly, take motor out, found the coupling is broken. replace the coupling, put back everything. That's all. Washer start to work immediately.
Parts Used:
-
Wenliang from Sidney, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
Agitator would not work
-
Gregg from Mandeville, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
water pump went out
had to take the entire shell off the washer and then it was 2 simple clamps.
Parts Used:
-
Melissa from Westville, IN
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Agitator and drum would not turn, but water would pump out
Watched the video on this sight. Fallowed instructions in video and everything went very smooth.
Parts Used:
-
John from Prosperity, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Agitator would not move or spin
Unplugged, removed water supply hoses, removed drain hose from washer, laid whole washer on it`s back without removing the cabinet, popped clips off the water pump and laid to side, took two screws out of clips that hold motor on and popped them off with a screw driver, unplugged wiring harness and another single wire on motor and then lifted motor off. Then pried the plastic pieces of the coupling off the the motor and transmission shaft. Cleaned debris off motor and washer, replaced plastic piece to the transmission and set rubber part on plastic. Then replaced new plastic piece on motor and set motor back into bracket and put all parts back on in reverse order. I make it sound hard but was a easy job.
Parts Used:
-
Donald from Orlando, FL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
water leak
disconnected the power, the water supply hoses and took the drain hose out of the wall. Tilted the washer back, undid the 2 clip,took the pliers slid the clamps back. Installed new pump. Put everything back. Done.
Parts Used:
-
thomas from Eureka, MT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
Was this instruction helpful to you?
Thank you for voting!
Washer Stopped And Could Smell Smoke
I followed the video on replacing the direct drive coupling. It was easy to follow and gave step by step instructions for screw locations, fastener and part removal and installation.
Parts Used:
-
RONALD from OSCODA, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Washer spun at about a quarter speed
The spin cycle was super slow leaving clothes soaking wet at the end of a full wash cycle. Ordered a clutch repair kit, watched the how to video that was e-mailed to me with my order while I did the repair and got it done in about 45 minutes. This was my first true appliance repair outside of maybe a busted fuse or replacing the heating element in a stove. Never thought taking the motor, transmission and clutch out of the washer and putting all back together would be so very simple. Meanwhile my wife is pissed because she thought she might be able to go get a brand spankin new washer...until I fixed the old one. Thanks for saving me some dough PartSelect.
Parts Used:
-
Mike from Powell, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!