Models > 11027042600 > Instructions

11027042600 Kenmore Washer - Instructions

All Instructions for the 11027042600
91 - 105 of 106
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
replaced leaking pump
Easy repair. Went to You Tube and saw PartSelect video. The best instructions...should make a link from parts page to video of install. Also replaced Heat element on Dryer. Watched video first.
Parts Used:
Drain Pump
  • richard from asheville, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
Lots of gunk between fabric softener dispenser and where it attaches to the agitator
Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!
Parts Used:
Seal, Inner Cap
  • Gregory from Sandy Springs, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
did not work
reemplace the lid lock assembly
Parts Used:
Lid Lock Assembly
  • JESUS from PORT ARTHUR, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
water leak at pump, crack in pump housing
First off always remember to empty all pockets, coins etc ruin pumps.shut off water supply, unhooked water lines and drain into pan.tilted machine forward so i could work on pump which is located lower left. drain pan under pump area, removed 2 rubber water hose's 3 5/16 screws with nut driver. Very carefully un clip rear of housing and removed wire harness. installed new pump
Parts Used:
Drain Pump
  • Janelle from Gray, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Parts Used:
Outer Tub Assembly
  • Elijah from Point Hope, AK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
washer wouldn't go in the spin cycle-
Pulled washer from back of wall and disconnected power source. I removed three screws in back that houses the ol motor control board. Also, I had to pull the front control knob off so that I could lift the cover to expose control board. I took several pictures of the motor control board before unplugging the wires just in case I forgot where the wires needed to go. Very simple process and had machine working within 15 minutes.
Parts Used:
Electronic Machine and Motor Control Board
  • william from germantown, TN
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
My lid lock assembly was bad and therefore the washer lid would not lock to allow for washing.
Went to youtube.com and watched the video that took you step by step in replacing the lid lock assembly.
Parts Used:
Lid Lock Assembly
  • Kelly from Petersburg, WV
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
noisy
Removed old tub assembly and installed new tub. Job took a little longer due to first new tub arrived damaged and I had to partially reassemble machine temporarily until second tub arrived.
Parts Used:
Outer Tub Assembly
  • Donald from Ormand Beach, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
f1, code on the face plate of the washer,we kept on resetting it
we ordered a motor controller,pop out the old one,then replaced it with the one we ordered,and bingo,problem is solved
Parts Used:
Electronic Machine and Motor Control Board
  • Delinda M from Chicago, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
noisey water discharge pump
PLASTIC motor housing gets hot and become loose. causing bearing to spin and make noise . Replaced motor that was quick and simple by removing 3 screws and 2 hose clamps , pluged up motor and begain washing again with no problem . Just wish motor housing was not plastic .
Parts Used:
Drain Pump
  • MEECHE from LANCASTER, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Parts Used:
Electronic Machine and Motor Control Board
  • Bonnie from Baytown, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Parts Used:
Suspension Rod Kit - Set of 4
  • brett from seymour, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
washing machine showed F50 code
I watched a video on how to do it.it wasn't very difficult the hardest part was getting the machine out of the laundry room and laying it over
Parts Used:
Rotor Position Switch Kit
  • david from knoxville, TN
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Hole in casing of drain pump due to loose nickle being pulled into pump - No screen in inlet to pump
Pulled back off of washer. Removed Spring clamps from inlet and outlet of pump housing. Removed hoses. Removed three screws holding pump in place. Disconnected electrical plug connector. Reassembled in reverse order. Note: new pump had no isolators and pump motor cover looked like a rat had chewed it up; however, motor, pump, and hoses appeared to be new. Put it on without the motor cover and it works. Epoxied the old pump housing to seal it up and now have a spare.
Parts Used:
Drain Pump
  • CARROLL from HENDERSONVILLE, NC
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
vigoirously shaking causung UL code
Replaced rods with new set of 4
Parts Used:
Suspension Rod Kit - Set of 4
  • Josh from Lodi, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 11027042600
91 - 105 of 106
Back to Top