11021102010 Kenmore Washer - Instructions

It's pretty easy all I had the news just pop off the, frabric softner container, but the small plastic cap could not be pulled out by hand or neddle nose plyers. I used a hex key to hook under the plastic loops and gripped the other end with vice gripps. After the plastic cap came off I used a socket wrench to remove the one bolt and this only came out very easy. Then remove the small cylinder and had a directional COGS and it was easy to replace and reassemble

Took the softener mechanism off by pulling upward. Pried off the cap to the agitator with a screw driver then removed the center bolt with a nut driver. This did take a little effort since it had never been removed. Pulled the agitator out of the washer and cleaned all the parts of any soap residue accumulated over the years. Took the agitator and stood it on the floor placing both feet on the sides and pulled it apart. there is a ring inside that popped out along with the top part of the agitator and the small cogs fell out. Cleaned the two pieces and replaced the cogs, holding the main part upside down lowered the agitator bottom into place matching the four grooves after snapping the unit together slide the cog cover into place and gently replaced the agitator back into the washer and replaced the bolt tightly. Then snapped the softener attachment back into place. This required a good bit of pressure but snapped right into place. Done job. Saved a lot of money and a simple fix to a problem. Agitator now works just as it should, no slippage at all. Took about 30 min all together. You can go online to find installation directions for any brand washer that has a full size agitator.

Thurs. followed video directions, found the dogs to be defective and around 2 pm ordered dogs on line. To my surprise, on Friday around 11 am the dogs arrived. My husband installed them and the agitator is fine. I was so amazed at how quickly the dogs came. The machine was ready to go in less than a day. Thank you for your efficiency.

Pulled off the fabric softner holder, pulled out the cover for the agitator. Used a socket set to loosen the screw that holds in the agitator hub, pulled out the hub, removed the gasket from the cogs and replaced new cogs. Works like new!!!!

slipped up upper locking collar lifted off cover and removed 7/16 bolt that holds agitator in place. lifted out agitator and installed agitator repair kit. 123 simple. also next day delivery outstanding keep up good work

I just followed the steps on the video, I was surprised how fast I got the parts within 24 Hrs . Thanks

Remove protective cover and inner seal with gasket from top of agitator. Use socket set with extension to reach bolt in bottom of agitator and loosen bolt. Remove assembly from washer. Take out interior disk and remove broken agitator directional cogs. Replace with new directional cogs. Reassemble parts in reverse order. Easy Peasy,took about 5 minutes.

Popped top cap off agitator, removed bolt, removed top agitator, replaced directional cogs, reinstalled top agitator, bolt, cap. This machine is 43 years young, it's happy again.

Popped agitator cap. Used ratchet to remove screw. Pulled off base unit. Inserted cogs into slots after removing worn and or broken cogs. Reinstalled......done!

Followed instructions on WEB site, they were very easy.

watched the video piece of cake good job guys

Remove top cap to access 1/2" bolt. Remove bolt and pull entire assembly up and off of shaft.Disassemble unit by taking long std. screwdriver to release 2 small locking tabs. Flip over and remove ratcheting upper assemble from larger lower piece.Now you will see the broken cams and be able to replace.Assemble in reverse order.

Disassembled ,as assembled.

After some online research as what could be wrong with my washing machine. Several videos later, my bother found that it was the agitator, Thanks to the helpful video from Parts Select. We ordered the parts and within days the parts arrived. Installing the 'Agitator Repair Kit was really easy and took all of 15 to 20 minutes, most of which was looking over the drawing. My washer now works like a charm.. Thank you Parts Select for the speedy deliver my parts!

PartSelect has a training video for this repair. Remove the softener dispenser by popping it up with a flat screwdriver. Reach down inside the agitator and remove the bottom cap. Use a 7/16 socket on a six inch extension to remove the agitator bolt. At this point I recomment pulling the entire agitator assembly out for ease of disassembly and reassembly. Clean as necessary. Use a pair of needle nose pliers to remove the cog assembly. Place the cog assembly on a flat surface and use a flat screwdriver to remove the retainer. Note the position of the cogs and replace with the new. There are two plastic clips on the lower agitator that you can snap off to make reassemble easier. Replace the agitator in the tub. If you don't have a magnetic socket, I find it's helpful to place a small piece of paper towel across the socket to hold the agitator bolt in place as you slide it back down inside the agitator for reassembly. Tighten the bolt. Replace the bottom cap and softener dispenser.pa