11015732400 Kenmore Washer - Instructions

I had to unscrew 2 screws that held the control panel, then remove the 2 end caps, remove 2 screws that held the control panel to the washing machine. I then lifted the control panel and leaned the lower case forward. All this to get access to the ground screw for the lid mount. It sounds like a lot, but actually it was quite simple. I replaced the old switch with a new one and put everything back together just like new. No extra screws or parts that I could not remember where they came from. Thanks Parts Select. Reading the comments from others helped me to realize that I could do the work without worry. The only problem I had was ordering the correct part. That did not happen until I got the correct part number from the old part.

Disconnected old power cord inside control cabinet, removed strain relief , then removed damaged power cord. Reinstalled new cord with new strain relief.

Just removed the broken part and replace it with the new one.

unscrewed a bolt, pulled top agitator out and replaced parts and reinstalled.

Followed the video on the website. I removed the hoses from the pump rather than removing the pump as suggested in the video. Then separated the motor from the transmission and replaced the coupling; then reattached the motor and hoses. Lining up the washer cover and clamping it back on was the most trouble. But all in all, a easy repair.

Replacing the fabric softener dispenser was very easy. It just snaps on. Make sure you line up the tabs with the holes in the agitator, otherwise it will not stay on and will fly off and break in the spin-cycle. This is how the first one broke to begin with.

Removed end caps on control panel, removed two screws, lifted the control panel and rolled it back out of the way.
Undid clips and wire connection and pulled the cabinet off. Replaced the switch and put everything back together.
Easy job but helps to have two people to get the cabinet back on right.

Coupler is design to break when washer is overloaded or out of balance. Saves the motor from being burned out. Very easy repair. Unhook washer hoses and electrical plug...tip washer on side if there is no bottom to washer instead of removing side panels. Unhook clamps to water pump using flathead screwdriver. Water pump comes off without unhooking either of the two hoses. Remove 2 electrical connections and two clamps from motor using socket and screwdriver. Motor pulls out very easy...make sure you are holding motor so it does not drop onto floor. Remove motor mounting plate with socket. Remove old coupling using stubby flat screwdriver from both motor and transmission shafts. Install new coupling on transmission by placing a large socket onto plastic piece of new coupling and tapping lightly with hammer until flush with shaft. Install rubber piece of coupling...tap new plastic piece onto motor shaft using socket and hammer. Reinstall motor mount. Turn motor shaft so coupling pieces are aligned. Reverse order to reinstall motor and pump. I tilted the tub slightly when reinstalling the motor and pump as it is a tight fit...just be patient during this step.

The last step in this process is to go tell your wife that she in fact is NOT getting the new $2000 front loading washer and dryer set she saw at Lowes because you just fixed her washer for $20 including shipping.

It really is an easy fix...takes longer to unhook and move the washer than to replace part. Thank You Partselect for your excellent website and speedy shipping of product.

but switch fixed

I disconnect power from wall outlets. Turn off pipes and remove water hoses from machine. Clear machine making room to operate.
I removed two Phillip head screws from behind the console, press down lightly on console then flipped it back. Disconnect the lid switch by releasing the plastic clip. Used a screwdriver to release the 2 metal holding clips (one on each side on top of machine. Ease the case up slightly then pull back gaining access to the centrifugal switch which is mounted to the motor with one Phillip head screw. One end of switch was broken and disconnected. Motor was not keeping up. Discharged capacitor by grounding the terminals with an insulated plyers. Lift the clip on the broken switch then pull the connector off. With new switch in hand, remove each of the 5 wires from the old switch by using a needle nose pliers one by one and connect them to the new switch making sure each one is properly secured in please. Connect the new switch to the motor using the single screw. Secure the connector to switch. Replace case by tilting back about 45 degrees, slide under front frame of machine all the way then down inplace. Use the two metal clips to secure frame to rear panel. Reconnect lid switch. Return machine to usual spot, reconnect water hoses, turn pipes on make sure there are no leaks. Plug back into wall outlet. Washer was tried and all cycles were completed.

Basically I followed the great instructions provided on the Part Select webpages. I would consider myself to have more common sense than mechanical skill. I didn't want to have to keep going back to purchase more parts so I decided to buy the motor coupler (under $5), new clutch assembly (Under $30), new motor (under $160). The shaft on the original motor wore down to a cylindrical shape which should have been more of a rectangular shape to fit precisely into the motor coupler and provide the grip strength for the washer tub to spin. Usually the no spin problem is linked to a faulty motor coupler. I was glad that I had to removed the motor to reach the motor coupler because in my case the coupler had not failed. That is when I saw the motor shaft had worn. Since I had all the new parts I replaced them all and since 6/13/19 the washer is running like new. Oh, the problem was most likely caused by someone in my family "overloading" the wash machine one too many times over 11 years. Guy's / Gal's you can do this and save yourself from buying a new washer for between $850 - $1,200. My repair expense was under $240 including tax and next day delivery of my parts. Thanks Part Select !!!! Neil

I first watched a YouTube video on how to open up the machine. It was a breeze. I removed the part the hose attaches to where the water comes out and into the tub. The hardest part was removing the old hose clamps. Had I known I would have used new clamps. I took off old hose and replaced with the new one, it took longer because of the clamp issue. Otherwise it went fairly easy, to my surprise. Even tho I am a 70 yr old woman I will try to fix what I can. Doing this saved me at least $600. For a new washing machine. I'm so proud of myself.

Washer is 29 years old. Found that tub spring hooks into a simple (non-reinforced) hole in the base frame, and it had worn the hole through through the edge of the frame (key hole style). Due to age and low cost of parts, ordered all suspension springs, brackets, & pads. Once they arrived, took the tubs out (first time for that), found that the suspension pads looked fine, but the wear pads showed a lot of wear and the front one was snapped in the middle, perhaps an after effect of the spring failure. From my lack of attention, initially tried to get front pad into the wrong set of holes, a bad fit; corrected. Simply drilled a near-by hole in the base frame for the tub spring.

While the tubs were out, took them outside and scrubbed them clean. Also cleaned agitator parts using bottle brushes. Followed the PartSelect videos and owner comments for procedures, methods. Found that some miss some important info, but if you watch others you can combine the info to find what you need re disassembly/assembly.

At one point while attempting to remove the outer tub, did not realize that the screw that holds the rear spring bracket to the tub also holds the tub to the suspension plate.

Took me most of a day for the whole process, and I ended up with pulled/spasmic muscles from all the bending over, mostly from cleaning parts I think. Very helpful to have the parts breakout drawings, videos, others' experience.

I unplugged the machine.
Removed the back panel.
Located the switch, removing it and then following the wire to the plug, unplugging it.
replaced with new switch, plugged it in and replaced the back panel.
Removing and putting the back panel back was the hardest part.

After reading other repair stories I did it like they said. I disconnected all the hoses and drained as much water as I could. The top came apart easily with a regular screwdriver, a 1/2 in drive with extension, and a 14 or 15mm deep socket. The spanner nut came off easiest with several short, quick blows (punch and hammer, counterclockwise). In my case a good wack seemed to be soaked up by the wash tub springs. Be careful not to chip the tub.

I laid the washer, front down, onto a couple a 2x6's. I supported between the tub and body with small 2x4 scraps. The motor/trans/pump came off easily after disconnection the 2 hoses (towels handy) and wiring. After the 3 screws, and some wiggling, the assembly slid out nicely. The coupler came out after snapping the springs off to remove the pump and motor. A 1/4 nut driver and regular screwdriver assisted. Watch how the pump comes off. You might want to mark its orientation with a marker or something. Make sure you get the new coupler on all the way with some taps on the CENTER where the shaft is. Reassemble in the reverse order. You'll know why I suggested marking the water pump.

Watch the order/orientation of the springs, clips, and washer. The clips came off with a screwdriver and pliers. It's always nice to have a rag on them when removing, they like to shoot off and land in the spot that's hardest to find, like under the dryer. My clutch was assembled with the right spring and slid right on. Don't forget about the plastic washer, snap it in good. The plastic piece still on the washer was simple. I opened up a nose pliers and put it on each side of the clip then gave it a hit. It came off with minimal effort and didn't spin on the shaft like pushing on one side with a screwdriver.

During reassembly I put a very light film of grease on the shaft. That washer with the tabs gave me trouble at first. I put a good film of grease on the side with the tabs to hold it in place, with the tabs down, in the clip. Otherwise when sliding the assembly back together it comes loose and you won't get the motor/trans all the way in. Then it all has to come back out and you'll wonder what the heck is keeping the transmission from seating in all the way. You might even get it all together, figuring the motor or tub has to turn to get it to seat right. You may even try running a no clothes load and get stuck with a tub full of water. Ask me how I know.

Reverse everything to reassemble. Make sure you get the springs tight that hold the hoses on. I was worried about over tightening the plastic nut with a 1/2 drive. Run no-clothes load, large, hot with soap. I think tipping it over loosened some stuff that was stuck in between the tub and basket. No, it wasn't grease from the shaft, light film. Anyway, I'll waste a washer full of hot soapy water to avoid the, "Um..what's this on my new shirt".

I didn't mean for this to be so long winded, but I was leary about tackling this job at first. I know my way around the garage/cars, but never tried appliances before. I pictured it'd be apart for weeks and I'd have to call a repair man. Then the "I told you so" look would come. You all know what I mean. I just want to cover as much as possible and encourage others while having them avoid any troubles.