1100PRA-K Magic Chef Range - Instructions

My brother-in-law did the repair as I am a scardy-cat and didn't want to tackle it myself. The most difficult part of the repair was the awkward position you have to get your body in to do the repair. Other than that it was a piece of cake.

We replaced Flat Style Oven Igniter simply by removing the oven racks, then removed the bottom of the oven. Used a Philips screwdriver to remove the old igniter, placed new one in. The wires to the oven from the ingniter just needed to be in a clip. Tightened the screws and replaced bottom & racks. Oven worked wonderful after this, like a brand new oven!

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

the igniter would glow but the gas would not flow...
i would have guessed the valve was bad, but every one else thought it was the igniter.. they were right. verry easy to install. the stove worjks like new.

removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven works properly. Thanx!

Removed Old Igniter and installed new one, parts and connector fit fine, no modifications needed.

Un-did the old one put in the new. Iam 63 years old and a woman. Repair men wanted 500.00 plus to come out and repair I did it for cost of igniter in 15 min. Oven works great! Thanks parts select for making it so easy!

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

Removed the two screws that support the hot surface igniter. Removed the rear cover to disconnect the igniters wire harness and removed old igniter. Installed replacement igniter by fastening with the old screws and sending the plug harness through the ovens rear opening. Connected igniter into the harness and installed the rear cover.

I unpluged the oven, removed the oven door by slideing it off the hinges, removed the racks, took the bottom pan out exposing the igniter,while attempting to remove the 2 screws holding the igniter to the bracket, I discovered that they where stripped so I had to use vise grips to remove them. I went to the hardware store bought replacements and installed the igniter. I then removed the protective cover over the wires, stripped them put on the wire nuts provided with the kit put the protective shield back pluged the unit in turned it on, checked it, then put it back together. The stripped screws were the only difficult part.

I removed the two screws that hold the element. This took most of the time because one of the screw broke. Then I unplug the power,took the igniter out and disconnect the wire and reverse the procedure.

I unpluged the electrical cord first. Then pulled the stove away from wall. Next removed oven racks, the bottom of the oven. Then removed the deflector plate over the burner. The next step I removed the broil pan. Now the oven area is empty. Nice and easy to remove the igniter with nut driver. Two screws and wire nut that are behind the stove wall. Now I just reversed the procedure. Very easy. The only thing I'm not sure where the insulation block go's. The wires go through back oven wall hole. There was no insulation there before? So I put a small piece just behind the igniter over the wire. Will this catch fire I don't know? If someone knows let me know. Other than that it works.

put it on, perfect

installed new control unit had to use the old dial so it would match . Toughest part is the cleaning! needed it.

I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.