10663144301 Kenmore Refrigerator - Instructions

Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

We thought that the problem was with the inlet valve, perhaps dispensing too much water and causing the overflow that caused the leak. Installation of the valve was easy, but it didn't fix the leak. After some more tinkering, we discovered that the problem was that the ice maker itself had gotten out of kilter, that the rear part was tilted down too far and was causing the overflow that created the icicle. The rear part of the unit needed to be raised by adjusting the rear screw that attaches the ice maker to the refrigerator. Easy to fix that, and so far, no more leak. It didn't hurt, though, to get a new valve and be forced to clean out the back of the fridge, as well as replace the copper water inlet tube with a plastic one.

I unplugged the refrigerator(for safety). Using a 1/4" nut driver I removed 1 screw holding ice tray rack. I then removed the 2 screws holding the lower shroud inside the freezer section. I then removed 1 screw holding cover plate where ice maker would be and disconnected the ground wire from the back panel. I then removed the 2 screws holding the back panel in place. This allowed me to removed back panel from from inside the freezer. I removed the fan blades from evaporator motor by pulling straight away from motor. I was then able to disconnect the power wires and the ground wire from evaporator motor. Using the 1/4" nut driver I removed the 2 screws holding the front motor bracket and removed the evaporator motor from its bracket housing. Using the an electrical cord that i had fashioned with two female spade connectors on each lead of the wire, i connected these to the motor and plugged the male end of the electrical cord into a standard 110v outlet to verify that the motor was in fact the defective component. The motor did not operate so I replaced the evaporator motor with a new motor and put everything back in reverse order. The refrigerator is running like a champ and keeping the refrigerator contents a cool 42 degrees. Thanks PartSelect.com

the repair it good and easy ,vo helper to do it.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH

Simply done !

read your trouble shooting guide, ordered the parts, plugged them in and every thing work fine.

Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!

I order the suspect part before pulling out the ice tray and whole ice maker for inspection. As it turns out my ice tray was peeling and all gunked up and I needed a new one. I suggest in the case of ice maker issues that you pull the entire ice maker before ordering what appears to be the troubled part. I had to replace the whole ice maker which was not really that much more money than just the part.