10663142303 Kenmore Refrigerator - Instructions

About 7 screws total. ! screw holding side shelf removed. 2 screws holding bottom rear panel removed. 2 screws holding rear panel top removed. 2 small screws holding the fan motor bracket. Remove 3 wire connectors from fan motor and then remove plastic fan(pull off) Then just reverse the procedure. As always please make sure unit is unplugged. If there is ice buildup in freezer use a blow dryer to melt and then dry unit. Very easy fix!

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

I watched the repair video. My son followed my instructions. He removed the ice-maker. The back panel was frozen, so we chipped and waited for the ice to thaw. There are three wires to remove from the old fan. My son used his cell phone to take a picture of the correct wiring. He used needle nose pliers to get the motor off the bracket. I used hot water to thaw the ice, so we could get the back panel to fit properly. If we weren't waiting for the ice to melt, we could have finished in about a half-hour. I'm 86 years old, and have carpel tunnel. My son is 63. Together, we make a good team.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

Took the food off a temporary shelf I fixed up from old parts of something else and slid in the new one after taking off 3 stickers.

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

I compared my problem to those on this site's problem descriptions. Others had the exact same issue so I felt confident about the fix and ordered a new thermostat. All it took to fix : Unplug fridge, use a 1/4" nut-driver to remove one screw, drop the panel, pull off temp knob, unhook 3 wires, pull out thermostat, remove plastic tube on sensor, replace plastic tube on sensor of new thermostat. Reverse assembly, done in 15 minutes. This is a simple fix, anyone can do it. (Total repair: $74.00)

My grandson did all the installing, he is really good at anything he goes to install, needs to look into something for him in this catagory, he said instruction sent was really easy to understand, will order from part select again. Thanks!

Ordered new set and installed

I unplugged the refrigerator(for safety). Using a 1/4" nut driver I removed 1 screw holding ice tray rack. I then removed the 2 screws holding the lower shroud inside the freezer section. I then removed 1 screw holding cover plate where ice maker would be and disconnected the ground wire from the back panel. I then removed the 2 screws holding the back panel in place. This allowed me to removed back panel from from inside the freezer. I removed the fan blades from evaporator motor by pulling straight away from motor. I was then able to disconnect the power wires and the ground wire from evaporator motor. Using the 1/4" nut driver I removed the 2 screws holding the front motor bracket and removed the evaporator motor from its bracket housing. Using the an electrical cord that i had fashioned with two female spade connectors on each lead of the wire, i connected these to the motor and plugged the male end of the electrical cord into a standard 110v outlet to verify that the motor was in fact the defective component. The motor did not operate so I replaced the evaporator motor with a new motor and put everything back in reverse order. The refrigerator is running like a champ and keeping the refrigerator contents a cool 42 degrees. Thanks PartSelect.com

the repair it good and easy ,vo helper to do it.

I was pleased with the new ice maker and how soon I received it. I was disappointed because there were NO installation instructions that came with it. There were only service instructions that came with it. I contacted partselect and was told that they get the part from whirlpool and they are responsible for everything and was given a phone number to call. I called Whirlpool and was informed that they don't provide installation instructions, I said that on the web page is boldly displayed an installation instruction sheet. Whirlpool said that they expect that the installation person knows what they are doing. I let it go and was very careful taking the old one out and installing the new ice maker and the new pump.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna