10660187000 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Broken rear support wheel
remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.
Parts Used:
-
Adam from Freeland, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
Was this instruction helpful to you?
Thank you for voting!
Ice maker not working
I followed the video instructions to replace the ice maker controller. Works like new. Each to order from website, part arrived in 3 days. I'll certainly order from partselect.com again.
Parts Used:
-
Greg from Cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice mold was leaking causing all the ice to freeze into one chunk.
Got the main bolts off and unplugged and removed the ice maker. Had to remove all parts and rebuild it on the new mold. Was more complex than I thought but was able to get it done. Note where everything was as you take it off and you'll do fine.
Parts Used:
-
Douglas from Spring, TX
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
How to get timer out of defrost cycle?
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Parts Used:
-
David from Virginia Beach, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
Was this instruction helpful to you?
Thank you for voting!
light would come on and off
-
Dora from Rock Island, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Water was not getting to Ice Maker
Pulled Fridge from wall
Unplugged the fridge
Shut off water supply
Removed cardboard dust cover with ¼ inch nut driver
Unplugged wire harness from switch
Used small adjustable wrench to remove water line from input side of valve
Used sharp knife to cut water line leading to ice maker (compression fitting)
Used ¼ inch nut driver to remove water valve
Installed new valve in reverse order
Time taken, 10 minutes
Unplugged the fridge
Shut off water supply
Removed cardboard dust cover with ¼ inch nut driver
Unplugged wire harness from switch
Used small adjustable wrench to remove water line from input side of valve
Used sharp knife to cut water line leading to ice maker (compression fitting)
Used ¼ inch nut driver to remove water valve
Installed new valve in reverse order
Time taken, 10 minutes
Parts Used:
-
Charles from San Antonio, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
The wire harness plug was male .Same as the plug on the refrigerator
I cut the plugs off and bought male and female wire conectors and crimped them on the wires and pluged them together.
Parts Used:
-
Christine from Burnsville, WV
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Self Defrost Cycle Not Working
Bimetal Defrost Thermostat: Per enclosed instructions. Defrost Timer: Per enclosed instructions. Working fine now ! Right parts, delivered right on time and very good instructions.
Parts Used:
-
Daniel from Edinburg, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Unit Would Not Produce Ice
Removed hinged door from front of ice maker. Removed screws from bottom of ice maker. Removed ice maker unit and replaced control board. One pin connection was burnt. Reassembled unit and it works fine.
Parts Used:
-
robert jr from east rutherford, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Frame was cracked and would not hold the drawers in.
Very easy to do. Crisper frame just snapped in and fit well.Very happy with results.
Parts Used:
-
Sally from Freeville, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Evaporator Would Freeze Up And The Food Section Could'nt Cool
-
michael from buchanan, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
icemaker does not make ice...mech cycles normally
I decided not to open the package containing the Control and motor asm because the old one looked like it was cycling properly. I chose to try the inlet valve first, so I ordered the inlet valve and returned this part unopened after replacing the valve asm. It took a week to receive this part and just two days to get the valve.
Parts Used:
-
Don from Lanham, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
right front wheel broken off ...couldn't roll refrig out
Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!
Parts Used:
-
ROBERT from Pilot Hill, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Wrench set
Was this instruction helpful to you?
Thank you for voting!
Two cracked/broken crisper drawers.
1.Slid out old cracked drawers 2.Slid in new crisper drawers Simple! It took longer to open the shipping boxes than to install the new drawers! Problem solved! If only all fixes were this easy!!
Parts Used:
-
Terri from Natchez, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!