Models > 10656676501 > Instructions

10656676501 Kenmore Refrigerator - Instructions

All Instructions for the 10656676501
1606 - 1615 of 1615
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer was cold refrigerator was too warm.
I knew that if my freezer temp seemed Ok and my refrigerator was too warm that I should be looking to see if my evaporative fan was working. It blows the cold air from the freezer through to the refrigerator. Turns out that the unit was working and I figured out by viewing other customer experiences there was a diffuser door that opens and closes with a thermostat that was not operating. Replaced it and everything is fine.
Parts Used:
Air Diffuser
  • Larry from Hatboro, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.
Parts Used:
Icemaker Control Assembly
  • Donald from Banning, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker would not make ice
A repairman wanted $600.00 to fix our ice maker. I paid him $88.00 for his "service call" & asked him to leave. I ordered & replaced the ice maker machine & the ice maker still would not work, so I replaced the 2 optics boards next. Replacing the ice maker was most challenging because the plug is so hard to get at, but the 2 optics boards were pretty easy. Just watch the video on PartSelect.com. Work slowly & take your time when pulling out & replacing the optics boards. There were a total of 6 screws for the 2 optics boards. It took me approximately 10 minutes to replace both boards, & now my ice maker is working perfectly! I am thrilled!!
Parts Used:
CNTRL-ELEC
  • KATHRYN from BOISE, ID
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped working. Already replaced Photo Eye
Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.
Parts Used:
Icemaker Control Assembly
  • Alfred Van from Lutz, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
None
Watched the video it was right on, no problem.
Parts Used:
CNTRL-ELEC
  • Roger from Hampton, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
refrigerator and freezer would stay frozen.
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.
Parts Used:
Bi-Metal Defrost Thermostat
  • Jack from Poplarville, MS
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    More than 2 hours
Was this instruction helpful to you?
Thank you for voting!
no problems
Watch the movie adjacent to the part on the ordering list,follow said instructions you can't miss.Thanks for the movie,the ease ordering the friendly associate that took my order and your timely shipment.Once again thanks for everything.Thomas J
Parts Used:
Ice Maker Assembly - 8 Cube
  • Thomas J from Jackson, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Broken Door Bin
Easy and amazed at how fast my order was processed. I received the parts next day. Wow!
Parts Used:
Refrigerator Door Shelf Bin
  • Evelyn from Redwood City, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice maker defective and ice mold delaminating
Repair was easy. But what I really liked was the prompt/timeliness of the correct part delivery. That's what really made the difference. (My ice bucket is FULL of ice).THANKS!!
Parts Used:
Ice Maker Assembly - 8 Cube
  • Darryl from Plano, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
No Ice
Watched video
Parts Used:
CNTRL-ELEC
  • Gerald from Sarasota, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 10656676501
1606 - 1615 of 1615