10651552100 Kenmore Refrigerator - Instructions

1. Remove 3 phillips head screws with #2 phillips screwdriver. 2. Gently pull mounting bracket outward from freezer case. 3. Using fine needle nose pliers remove clip washer from lower end of flipper mounting rod. 4. Note position of flipper spring and pull mounting rod upward far enough to insert downward through new flipper and spring. 5. Install clip washer removed in step 2. Position assembly onto freezer cabinet and secure with screws removed in step 1.

The Sears man came out and told me it was the thermostat that needed to be replaced and it would cost $321 plus tax. I went on youtube and watched the Partselect video several times and decided to order the part after seeing how easy it was to install. Total cost $65. I put the laptop on the counter and watched it as I installed it. It helped that I could go back and watch a certain part if there was a problem. But I had no problems and installed it in 20 minutes. Very, very simple to do. Of course I had to pay $75 to the Sears man but I saved about $200 . Thanks Partselect.

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

took screwdriver, took out old parts. replaced with new parts. plugged fridge back in, turned on receiver. We have ice! Real Easy to install! Thank you Part Select.

The hardest part was figuring out how to get the front panel escutcheon panel off. With the putty knife under the bottom flange, you need to push down with some effort on the part of the flange where the drip pan slides in and twist the putty knife to disengage the locking tab. Once the panel is off, the rest of the job is easy with the aid of your video. Everything works like new...thanks.

Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.

I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.

I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.

A repairman wanted $600.00 to fix our ice maker. I paid him $88.00 for his "service call" & asked him to leave. I ordered & replaced the ice maker machine & the ice maker still would not work, so I replaced the 2 optics boards next. Replacing the ice maker was most challenging because the plug is so hard to get at, but the 2 optics boards were pretty easy. Just watch the video on PartSelect.com. Work slowly & take your time when pulling out & replacing the optics boards. There were a total of 6 screws for the 2 optics boards. It took me approximately 10 minutes to replace both boards, & now my ice maker is working perfectly! I am thrilled!!

Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.

Watched the video it was right on, no problem.

I checked to see if the compressor was running and it was not. I check the defrost fan and the compressor fan and they both were running. All lights were on inside the refrigerator. I then checked the compressor connection and using the multimeter I check for voltage on the two wires going to the compressor and I had 120VAC on the terminals. I then removed the start relay off the compressor as well as the overload relay. I then check the OHMS reading on the compressor terminals and I had good readings. I shook the relay and it was rattling. At this point I search on the internet for the start relay and ordered the parts. Received the part in two working days. Replaced the components and bingo everything started working. It took me more time to troubleshoot the problem than it took to replace the parts. Vernon

I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.

Watched video