10651062100 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Freezer not freezing food
remove power. Remove rear cardboard panel.. Remove wiring from startup kit. Remove defective startupup kit. Then reverse procedure.
Parts Used:
-
conrad from LaPlace, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Garage refrigerator. Vauvle froze and ruptured.
Removed old valve. New valve does not provide for filter without modification. oOld valve used compression nut which had to be removed. Smooth cut with utility knife and push in. Needed a 1/4 inch compression coupling to hok up ice maker connection to 1/4 inch plastic hose fro the valve.
Parts Used:
-
Thomas from Indianapolis, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Temperature flucations
I watched the video a few times and pretty much did as it said to do. Took about 20 minutes start to finish. It seems to be working 100%.
Parts Used:
-
Charles from Owensboro, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Ice maker quit working
I found the part I needed at parts select and followed the video on their web site. They have a very informative web site, it made my job easy. I highly recommend this company.
Parts Used:
-
Donald from Banning, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Very noisy operation
Removed and replaced the condenser motor fan kit. This was a very easy tear down and replacement of a bad component. Removed 4 screws to remove the bracket holding the fan motor kit pulled it out and replaced with the new unit (4 screws supplied) plgged in adapter cord (supplied) and re-installed took about 10 minutes.
Parts Used:
-
Mike from Coon Rapids, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped working. Already replaced Photo Eye
Top left mounted Icemaker facing front. Disconnect power to fridge. Using 1/4" nut driver remove single silver nut under right rear side. It holds a plastic cover over the electrical connection, unhook the cover and remove it. Release clips under front lip under both sides and entire icemaker will slip and twist out. Remove electrical connection to ice tray. Place assembly on bench and remove 3- 1/4 hex screws from under side to release bottom tray. Snap cover off motor and remove. Carefully align pin and arm on control assembly to ice tray and-re assemble. May take 30 min to dispense. Discard till clear.
Parts Used:
-
Alfred Van from Lutz, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
overloads melted
installed o/l unit which was #1 on instruction sheet ,very easy, pluged side by side refrigerator freezer in ac outlet, checked amps on compressor, and a very happy ending! THANKS!
Parts Used:
-
albert from westwego, LA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
refrigerator and freezer would stay frozen.
I shut the unit off for about ten hours and when I turned it back on and set the temperatures for the freezer and refrigerator it has been working great.I will keep the part in case it happens again.
Parts Used:
-
Jack from Poplarville, MS
-
Difficulty Level:Really Easy
-
Total Repair Time:More than 2 hours
Was this instruction helpful to you?
Thank you for voting!