Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Ice maker wouldn't cycle
Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.
While trying to get my icemaker to unjam (ice all stuck together) I broke the coupling under the ice bin. Shouldn't have tried to force it, but you learn from experience... I found the diagram of what I needed to order on the website and ordered the part, which arrived in about 2 days. Dumped the ice out of the bin, removed the screw that held in the broken coupling, replaced the coupling and replaced the screw. Put the ice bin back into the freezer door and Voila.. ice dispenser works again.
Removed the Wiring & Troubleshooting instructions from behind the front Grill and used to troubleshoot the KSCS25IN side by side refrigerator. I then removed the three screws from the Emitter assembly on the left side of the freezer. Then disconnected the four pin connector. Removed screw holding emitter PCB to housing and replaced with the new PCB and then re-installed. Similar steps for the Receiver assembly and PCB on the right side of the freezer. Unit started making ice after making some water level adjustments on the Timer assembly.
I did an internet search about the problem and found the information and experience that other people had. Ordered the part and that's it. One important thing to remember is to unplug the power supply of the appliance prior to making any repair. I short circuited the original board when I tried to plug it back in after cleaning the optics. (The board might have been bad before that.) The red light stop working but the frige is making ice non stop!!
I first had a technician come out to the house and he wanted to charge nearly $300 to replace the icemaker unit. I told him he was "high" and began doing my own research of the problem. That's when I found this website (thank God!) and read the notes from other customers. I figured out the secret location of the KitchenAid icemaker troubleshooting guide (why they hide this information I have no idea -- it's ridiculous), and performed the diagnostics to determine the exact problem. That is how I discovered that the emitter and receiver control boards were bad and not the icemaker motor module as the technician had tried to tell me. Good thing I didn't pay him, because my icemaker still wouldn't be working! The electronic control boards are a piece of cake to replace -- just 3 screws on each. Be careful with the electronical connectors since they snap in - don't pull on the wires, first unhook the snaps holding the wire connector to the board and then disconnet it. Once I replaced the boards I turned my refrigerator back on and immediately I heard the water running to fill up the icemaker and not much later I heard my first piece of ice hit the bucket. Woohooo!!!! It feels nice to fix a problem myself for a reasonable price. This site rules. I'll be coming here again in the future!!!
Emptied the ice holder, then removed the two screws located in the bottom of the ice holder. they were holding the metal cover in place, once removed I was able to remove the entire rotating ice prongs which moved the ice into the chute. I had to do this because the screw that held the coupling on could not be removed (too tight) Once the entire rotating device was removed I could easily remove the screw and replace the entire assembly.
The icemaker would not produce ice because the motor that pushed the cubes out had failed. The original icemaker failed in this way and we had the icemaker replaced by Sears Service for about $200. The second icemaker failed for the same reason after 18 months. I decided to do the repair myself t
Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".
To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.
The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet. Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.
Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.
The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.
Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.
Once the motor module is seated, replace the 3 screws and push the white cover back on.
Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.
Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.
The icemaker should start making ice within 2 hours.
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
water filter not seating properly to allow water flow, replace filter housing.
Turned off water to frig and unplugged power. Removed screws holding water valve in back of frig in order to release water line going to water filter housing. Removed screws holding water filter housing in front of frig and disconnected two water lines going to water filter housing. Removed water filter housing and replaced with new. Reattached the two water lines to the new filter housing and remounted with two screws. Reattached water line to fill valve and remounted fill valve. Plugged frig back in and tested water flow out of water dispenser, good flow now to water dispenser and ice maker.
Woke up to a wet wood floor and rug due to inlet tube spinging a leak/cracked. Watched repair video on utube. Ordered the part. And did the repair. But the other parts that the tube connects to started leaking due to age I assume and moving things to reach the part that tube went to. Old parts started leaking when I turn water back on. So now I have to replace the inlet valve and filter sleeve next. Hoping that will solve the issue and have ice again with out a wet floor and rug.
Replaced door gasket and hinge closers on Refrigerator door.
I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.
My water line to refrigerator sprung very small leak due to years of rubbing on its own bracket holding it to back of refrigerator. The removal and installation are exactly like shown in the video on PartSelect website. A possible problem can arise when removing and re-inserting the water line into "colletts" on the refrigerator filter housing. The grey circular colletts push in and out, not far, but after years of use can be brittle. If you move the colletts too much, a small part of plastic can snap, and you will then need an entire new filter housing. Be gentle when depressing the collett to pull out and push in the water line.
