10644029600 Kenmore Refrigerator - Instructions

I followed the instructions on the information sheet provided as well as watching a demo video on YouTube. Actual replacement of the emitter and receiver boards took only 5 minutes, but I was not sure it was working till I could here the ice maker harvesting the cubes. Still wanted to be sure so I kept an eye on it for a few hours. Each time I looked in there was more ice. I am so glad I found your website. Parts were about $106. Labor would have cost that much and the repair guy I talked to on the phone said he would probably have to replace the whole unit.

Used the trouble shooting off of YouTube and after finding that the heater was not at the right resistance, ordered a new ice-maker and installed. Very simple and a lot cheaper than going through Sears.

Watch the video was very helpful. I'm just a women and I did it all by myself. Thanks for the help of the video.

Turn ice maker control off,hold up front cover remove two screws, remove cover, remove rear screw on the back right side, slide unit part way out, make sure flipper on left is out of the way, unplug connector on right, remove unit,remove bottom cover & put on new unit,install in reverse order, turn ice maker control on, done

I went on line and found your web sight. There was a list of the parts by number and I clicked on the rilght one. It brought up a video for repairing it myself. It was so simple. I just followed your instructions and within an hour I had ice. It makes so much ice I'm going to have to give it away. No really its great.

I got the new part and unplugged the refrigerator. I removed the wire auto shut-off. I removed the old motor assy. I checked to see if the motor quit running at the same locations as the new one before removing the entire ice maker. Lucky it did, so I installed the new motor assy without having to remove the ice maker. It took 10 minutes at the most.

I read the other replies and decided to replace the boards. It worked!!!! Ice right away!!! I would have only needed to chafe that if I didn't muscle the ice maker arms around in frustration and brek it!!! This website is great!! Parts came fast and accurate !!!! Thanks parts select !!! Another satisfied customer!!!

Verified that the sensors were working. After removing the Ice maker assembly from the sliding track, I found that the indexed drive wheel on the motor had broken off from the shaft mounting. I ordered the Icemaker control and motor assembly from Partselect and swapped out the bad part. It only has three screws to remove and replace so it's fast and easy to fix.

Water was not filling the ice tray and the ice tray coating was comming off. After the service repairman wanted to charge me over 500.00 for just replacing the ice maker, it told him to take a hike. I bought the icemaker and the electronic controls, which controls when and how much water goes into the tray for less than 250.00 and it took me less than 15 minutes to replace.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

Remove ice storage container from inside freezer. Remove philips screw from the coupler underneath ice storage container. Removed coupler and flat washer. Installed new plastic coupling and metal flat washers. Relaced original coupler and screw. Tighten screws very carefully. Installed ice storage container and filled it with fresh ice. Ice is now coming out when the level on the outside of the freezer door is pressed. Yeah...

Pull the ice maker out using a nutdriver Pull the use a srew driver to remove the srews did the same to replace it put it back in had ice in 20 min

After googling for a parts supplier, PartSelect.com came up. The site was well done and had the Parts List conveniently available. I watched the associated video which was the highest quality "how-to" repair video I have seen. As it turns out, though, the icemaker does not have to be removed from the freezer unit. I removed the icemaker's shutoff lever, removed 3 screws, pulled the motor assy off, slid the new motor assy in place and re-installed 3 screws. Reinstalled the shutoff lever per the video and JOB DONE.

Ordered a new Ice Maker and replaced old one. The installation was a breeze except for the water recepticle on the right side of the Ice Maker. It was taller than the original and difficul to move the rubber water line into the new recepticle. Other than that. Problem solved. Been working great ever since.

This fridge is s ultraease 2 its 8 years old. Icemaker would'nt make ice. Its fairly easy all you do is take out the screws i recommend a power drill tho. Pop out the cover put the new motor in. I did'nt hear anyththing or see anything for a hour or two thought it did'nt work. Then i heard a clunk like ice falling into a bin. 3 hours later ice was falling frequently.