Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 10641563801 > Instructions

10641563801 Kenmore Refrigerator - Instructions

All installation instructions for 10641563801 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 10641563801
361-375 of 602
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broken door shelf

  • Customer: Roberta from Springfield, KY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy in about 2 minutes. snap the old out and slap the new in

Very loud clicking noise when opening/closing door

  • Customer: Ben from Port Saint Lucie, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I did it a bit different from instructions mainly because I disassembled it to troubleshoot before going on line to find part and "easier" instructions.I had a 5" block of wood and cut a shim to use with that to hold the door up. I got on my hands and knees with a mirror and removed the lower hinge plate then the screws holding the upper and lower cams. These both were quite worn so I just took them to my shop and with a hand grinder I rounded off the sharpo corners of the cogs of both cams and then reassemble the hinge plate and cams. This eliminated the loud clicking and the door closed easily but I was afraid it woulod not "Auto Close" when needed so I went online to find this page with the parts needed along with wonderful instructions. I ordered both upper and lower cams which came 2 days later (THANKS). I installed them my way since I did not want to empty the door contents and remove the whole door. I used the block, mirror and nut driver to R&R the bottom hinge plate and both cams. Time was still less than 15 minutes, Easy Fix, Thanks guys! Cheers, Ben

Replaced damaged pieces.

  • Customer: Thomas from Macomb, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered replacement parts from Parts Select on Sunday and the parts were delivered to my home on Wednesday . Could not be happier with this company. It was very easy to see exactly what I needed from the diagrams they provide on the website . Parts arrived and were installed in just a few minutes. I would, and have recommended Parts Select to my friends ... AWESOME !!

Small leak from icemaker

  • Customer: JOHN from VERO BEACH, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Simply removed the old icemaker and replaced it with the new one. Reqires removing 3 hex head screws and wiring harness, then reconnecting the new unit.

Heard a five second buzzing sound repeated 4 or 5 times per cycle coming from rear lower left compressor side.

  • Customer: Burton from Pecatonica, IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Light switch which turns on the lights when the door opens went out

  • Customer: Dennis from Lawrenceville, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

door of the refrigerator would not pull itself closed.

  • Customer: Roy from Council Grove, KS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The hard part of the repair was getting the wife to empty the refrigerator door shelves. Once that was done simply removed the three screws on the door on the top of the door removed the bottom cam located on the bottom inside of the door. One of the simplest repairs I've ever done. Watching the you-tube video was a great help.

you have to turn it off and on to run.

  • Customer: chris from woodland hills, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Just like the video showed me.It still does not work. Have to turn it off and on to make it start up.I also replaced thermostat in freezer. Does not work.

Solid ice on Evaporator coil

  • Customer: PRAKASH from PISCATAWAY, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
With service sheet, Enter service dagnostic mode, NO-6 is Desrost heater / Bi-metal Component status indicator shows 02 , it means Bi-metal is open, It should read 01,It's cover with Ice ( bellow 32 Dig. F )Mostly it open at 50 dig. F, To replace remove lamp cover and lamp + six hex screw with 1/4" nut driver, pull back cover ( with commen requirement to turn of power and deice the evaporator coil )out, bi-metal element is top at enterance of coil,cut both wire near bi-metal, join new bi-metal with wire nut or Insulated wire Jointer, Tape jonts proper,do neat work no hanging wire, Replace back removed parts back,Turn power back

Dryer was constantly running and not getting hot

  • Customer: HENRY from WARMSPRINGS, GA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removal of the old heating element was really easy. The video on Partselect.com was majorly helpful in reassuring my confidence in doing this repair.

Light in my refrigerator didn't work.

  • Customer: Joseph from Byron Center, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.

shelbes and drawer have cracks , so they needed replacement

  • Customer: Niurka from Raliegh, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
take out the old ones and put on the new, real simple. Thanks so much for the prompt delivery.

freezer and refrigerator compartments not cold enough

  • Customer: Michael from Colorado Springs, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Used the suggested problem list here to narrow down that the repair was most likely the run capacitor. Poped the new one in and I now have better control of my compartment ranges. I have a temperature gauge in each compartment. Check them every opening of the doors.

Cracked drip tray

  • Customer: Michael from Ft. Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed the rear water valve and water line, and front water filter which allowed me to remove the old drip tray. New drip tray is smaller than the original tray, so I needed to put blocking in to keep tray under drip spout. Refastened the water filter, water valve and water line.

Fridge and freezer not coming on without coaxing.

  • Customer: Howard from Victoria, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Been fighting this for over a year. Sometimes the fridge and freezer would heat up past the point it should come on. Had to slide the fridge temp control back and forth until the unit came on. Researched the problem determined the thermostat to be the issue. Got the part, finally found the time, then took the top tray out, popped off the escutcheon, unplug some wire and took out the control shuttle. Removed the old and replace with the new thermostat. Re-installed everything, plugged in it in and BAM. It's working. Now just fine tuning the slides to desired temps. THANKS PARTSELECT.
All Instructions for the 10641563801
361-375 of 602