01815 Briggs and Stratton Generator - Overview
Models starting with 01815
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Filter-oil
PartSelect #: PS8982169
Manufacturer #: 492932S
This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtrat...
$15.13
Special Order
Solenoid
PartSelect #: PS9064363
Manufacturer #: 691656
A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acti...
$35.85
On Order
Key, Lock
PartSelect #: PS9184142
Manufacturer #: B5053GS
This is an authentic manufacturer-sourced part which is specially made for Briggs and Stratton generators. It is an identical replacement for a missing or a faulty lock key that was included with a ne...
$11.41
In Stock
Washer, 5/16
PartSelect #: PS9999626
Manufacturer #: 703350
This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment...
$6.40
On Order
Switch, Set Exercise
PartSelect #: PS9160620
Manufacturer #: 87799GS
The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual repla...
$8.76
In Stock
Lawn Mower Flat Washer
PartSelect #: PS9999890
Manufacturer #: 703590
This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering sp...
$6.40
In Stock
Gasket-exhaust
PartSelect #: PS9307302
Manufacturer #: 806425
This is a genuine manufacturer-sourced replacement gasket which is specially designed for use with Briggs and Stratton equipment. It is utilized to provide an air-tight seal between connected pieces, ...
$7.90
In Stock
Screw, M5 - .8 X 10 Taptite
PartSelect #: PS9116859
Manufacturer #: 74908GS
This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cov...
$6.40
In Stock
Control Board
PartSelect #: PS8904244
Manufacturer #: 191652GS
The control board is made of durable materials. It is an original Briggs & Stratton part for use in generators. This item is available as an individual replacement part. A screwdriver might be necessa...
$386.41
Special Order
Rectifier, Battery Charge
PartSelect #: PS9054741
Manufacturer #: 65795GS
The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may...
No Longer Available
Exact Part matches for your search term
[Viewing 1 of 1]
Rotor Nut
This part number matches the current model number 01815
PartSelect #: PS10336668
Manufacturer #: 01815
No Longer Available
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Parts Used:
-
Bruce from CARNATION, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
15 of 36 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No voltage on secondary side of transformer. Confirmed with meter that transformer windings had infinite resistance.
1. Turn the generator selector switch to "OFF"
2. Remove the 240 volt fuses in the automatic transfer switch to remove power to the transformer.
3. Remove the outside cover from the front of the generator, on the motor end.
4. Remove the 3 screws from the panel covering the controls.
5. Label or make note of which ... Read more terminals the 4 wires on the transformer go to and disconnect from transformer.
6. Using 9/32 nutdriver, remove the two transformer mounting nuts and lock washers.
7. Remove old transformer from studs and install new one. Reinstall nuts and lock washers.
8. Reconnect the 4 transformer wires.
9. Reinstall the control panel cover and the generator housing end cover.
10. Reinstall the fuses in the automatic transfer switch.
11. Put the generator selector switch back in "Automatic"
2. Remove the 240 volt fuses in the automatic transfer switch to remove power to the transformer.
3. Remove the outside cover from the front of the generator, on the motor end.
4. Remove the 3 screws from the panel covering the controls.
5. Label or make note of which ... Read more terminals the 4 wires on the transformer go to and disconnect from transformer.
6. Using 9/32 nutdriver, remove the two transformer mounting nuts and lock washers.
7. Remove old transformer from studs and install new one. Reinstall nuts and lock washers.
8. Reconnect the 4 transformer wires.
9. Reinstall the control panel cover and the generator housing end cover.
10. Reinstall the fuses in the automatic transfer switch.
11. Put the generator selector switch back in "Automatic"
Read less
Parts Used:
-
Laron from GRAND RAPIDS, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!