LG Dishwasher Seals and Gaskets

Videos!

Your Price

$12.72

LG Dishwasher Pump Gasket

★★★★★

12 Reviews

PartSelect Number PS3535690

Manufacturer Part Number MFZ32863101

This is a pump gasket, also known as a pump housing seal, for a dishwasher. The gasket is fitted around the edge of the pump, preventing leakage between the pump housing and the filter housing. Located at the bottom of the dishwasher, the pump circulates and drains water from the dishwasher. Age and dishwasher detergents can dry out the pump gasket and cause it to fail and leak. Leak from the pump is not always noticeable until you remove access panels from your appliance. This part is made of rubber and is black in color. It is an OEM part from the genuine manufacturer.

Fixes these symptoms

Leaking
Noisy
Not cleaning dishes properly
See more...

Installation Instructions

Glen from LINESVILLE, PA

Dishwasher gave the Ne code

When I turned the dishwasher over I discovered the PS3579323 diverter motor had failed due to a leak around the PS3536016 valve, check. No use replacing the diverter motor without fixing the leak so I turned the machine back over and disassembled the spray arms and top of the pump cover which reveled the case assy and the valve, check. Upon removal of the valve, check I discovered hair wrapped around it which compromised the MO31 packing and caused the leak. I probably could have just cleaned out the hair and reassembled it but because my installation is a bit of a pain I elected to change the case assy (because of a slight depression where the packing sets) the M031 packing, the MO25 valve, check, and the MO35 pump gasket. After that was accomplished I turned the machine upside down and replaced the MO26 diverter motor and reinstalled the dishwasher. End result: Ne code cleared, no leaks and now the dishes are clean on the top shelf and the wife is happy. There are great instruction videos on YouTube. Good luck! Read more...

Your Price

$53.41

LG Dishwasher Door Gasket - Black

★★★★★

9 Reviews

PartSelect Number PS3522654

Manufacturer Part Number 3920DD3005A

This is a door gasket for a dishwasher. It creates a watertight seal between the dishwasher door and tub to prevent leaking while the appliance is in use. The gasket is approximately 76 inches long and is black in color. The gasket could become dry and brittle over time which can cause a leak, forcing you to replace it. After removing the old door gasket, clean the empty crevice to ensure a proper seal when you install the replacement gasket. To install the replacement gasket after cleaning the area, simply push the new part into place around the door.

Fixes these symptoms

Leaking
See more...

Installation Instructions

Bruce from Katy, TX

Dishwasher leaking; got AE error almost every other wash

The inside gasket deteriorates over time - However replacement is easy. the main thing you have to remember is after you remove the old gasket, install the new one starting at the middle top of the tub and work your way down both sides. Also, don't push the gasket all the way in...only enough to hold in place. When you close the door the gasket will form a better seal around the door. Read more...

Your Price

$49.56

LG Dishwasher GASKET

PartSelect Number PS12081631

Manufacturer Part Number MDS65210402

Fixes these symptoms

Leaking
See more...

Your Price

$34.45

LG Dishwasher Tub Seal

★★★★★

2 Reviews

PartSelect Number PS3575441

Manufacturer Part Number 3920DD3002B

Fixes these symptoms

Leaking
See more...

Your Price

$11.32

LG Dishwasher Packing

★★★★★

2 Reviews

PartSelect Number PS3522655

Manufacturer Part Number 3920ED4009B

Installation Instructions

Glen from LINESVILLE, PA

Dishwasher gave the Ne code

When I turned the dishwasher over I discovered the PS3579323 diverter motor had failed due to a leak around the PS3536016 valve, check. No use replacing the diverter motor without fixing the leak so I turned the machine back over and disassembled the spray arms and top of the pump cover which reveled the case assy and the valve, check. Upon removal of the valve, check I discovered hair wrapped around it which compromised the MO31 packing and caused the leak. I probably could have just cleaned out the hair and reassembled it but because my installation is a bit of a pain I elected to change the case assy (because of a slight depression where the packing sets) the M031 packing, the MO25 valve, check, and the MO35 pump gasket. After that was accomplished I turned the machine upside down and replaced the MO26 diverter motor and reinstalled the dishwasher. End result: Ne code cleared, no leaks and now the dishes are clean on the top shelf and the wife is happy. There are great instruction videos on YouTube. Good luck! Read more...