Kenmore Air Conditioner Fans and Blowers
Find your partEnter your model number or a part number and click "Search"
Take a photo of your product’s model number plate and upload it to find parts fast!
Here is an example model number plate:
Popular Kenmore Air Conditioner Fans and Blowers
PartSelect Number PS3528571
Manufacturer Part Number 5900A10011A
Sam from MCQUEENEY, TX
accumulated condensation caused condenser fan failurePull the unit out of cabinet. Remove the brace between the blower housing and the condenser frame. Remove the screws securing the the condenser coil to the base and carefully lift and angle it just enough for the broken fan to clear ( be very careful with the refrigerant lines ). Slide the new fan back on the shaft and secure with the spring clamp. I used a pair of vice grips to compress the clamp, but be very careful because the clamp can exit the pliers, if the jaws are not perpendicular to the clamp. If you live in a area with high humidity remove the rubber plug at the back of the unit or the condensation will break your new fan. This fan needs some changes in design because the condensation puts too much stress on the plastic that contacts the motor shaft - some metal between shaft and the blades would help. Read more...
PartSelect Number PS3528606
Manufacturer Part Number 5900AR1173AThe fan assembly or condenser fan blade fits on the motor shaft and circulates air over the condenser. This cools the refrigerant before it enters the evaporator. If the fan assembly in your room air conditioner is not operating properly, you will need to replace it with this part. This fan assembly has 5 blades and is approximately 14-1/2 inches in diameter. It is made of white plastic. You will need to open your air conditioner, and most likely remove it from the wall/window to complete this repair. Be sure to disconnect power to the unit before you begin this repair.
PartSelect Number PS2364358
Manufacturer Part Number 5304472356This part is a fan blade manufactured to fit on the condenser motor shaft of an air conditioner. The function of this part is to circulate air over the condenser to cool the refrigerant before it enters the evaporator. Be sure to disconnect the power to the air conditioner before doing this repair to ensure the fan does not engage while being replaced. It is recommended to check the fan motor while the fan blade is off. This is an authentic OEM part that is sourced from the genuine manufacturer.
Exhaust Vent Blower Wheel
PartSelect Number PS11757592
Manufacturer Part Number WPY707985This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
Janellen from Aiken, SC
blower motor diedPulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great! Read more...
PartSelect Number PS3528581
Manufacturer Part Number 5900A20009A
Joseph from BROOKLYN, NY
Fan BrokeLocal authorized LG repair shop told me, don't waste my time fixing it. Bench fix is $300 dollars. Purchased part, watched a video and bam. Fixed in 3-4 hours. Read more...
PartSelect Number PS3528610
Manufacturer Part Number 5900AR1508BThis fan assembly or also known as a condenser fan blade is used in air conditioners. The blade fits onto the motor shaft and distributes air over the condenser to cool the refrigerant before it goes into the evaporator. This part blows air parallel to the motor shaft which the blade rotates on to successfully circulate the air. It is made from white plastic. *Please note: This part is sold individually. This part comes with a slinger ring. Refer to the manual provided by the manufacturer for installation instructions and further guidance.
PartSelect Number PS819849
Manufacturer Part Number 309651003This is a fan blade and it is made for an air conditioner unit, it may also be known as a room condenser fan. The blade is black and has a roughly 13-inch outer diameter. The function of this piece is to blow air over the condenser, which will cool the refrigerant and eventually cool the area. The tools you will need to make this repair include a pair of pliers, a screwdriver set, and a socket set. Before making this repair, make sure to unplug your air conditioning unit.
James from Canyon, TX
condenser fan brokenpulled the cover off a/c, removed shroud covering fan. replaced the fan, reassembled a/c. works great.ty Read more...
PartSelect Number PS2379584
Manufacturer Part Number 5304476059
PartSelect Number PS2359391
Manufacturer Part Number 5304471287