Official Kenmore Air Conditioner Parts | Order Today, Ships Today

Your Price

$7.44

Light Bulb - 40W

★★★★★

63 Reviews

PartSelect Number PS884734

Manufacturer Part Number 8009

This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are most often used to light the inside of refrigerators and ranges. It features a standard socket base, which means you simply unscrew the burnt-out bulb and screw in the replacement. Depending on the appliance you may require a screwdriver or nut driver to access the light bulb. We recommend you wear work gloves while handling this replacement part. It is constructed of glass and metal and is sold individually. Depending on the appliance and location of the bulb within it, you may want to consider disconnecting power and using a flashlight for easier access to unscrewing and re-screwing in your bulb during this repair.

Installation Instructions

judie from mays landing, NJ

interior drawers were off their rollers

pulled the washer out and replaces the top roller system on both sides and the replaced the weels and brackets on the bottom drwaer. however i had trouble putting the dish washer back correctly and had to call a repairman to adjust the dishwasher and alighn it to open and close properly. but i did do good inside. i feel it was easy and a success. thank you for having the supplies for us to attempt to repair it on our own. Read more...

Silicone Rubber Adhesive - 2 oz – Part Number: WP279368

Your Price

$47.14

Silicone Rubber Adhesive - 2 oz

PartSelect Number PS11740605

Manufacturer Part Number WP279368

Silicone rubber adhesive is a high temperature adhesive that is used for gaskets on dryers and felt seals. It is used on many different appliances for many different application reasons. This silicone paste creates a waterproof seal between components. This product is a 2 oz. tube. Unplug your appliance if you will be working on any internal workings and applying this sealant. Wear gloves to protect your hand from accidently applying sealant to your skin. The surface must be clean, dry, and free from oil and grease. Coat one surface and let it dry for at least one minute and then bond.

Your Price

$9.24

Hex Nut

★★★★★

2 Reviews

PartSelect Number PS11742711

Manufacturer Part Number WP488130

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to wear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

Refrigerator Ice Maker Assembly – Part Number: 241798231

Your Price

$151.89

Refrigerator Ice Maker Assembly

★★★★★

75 Reviews

PartSelect Number PS12364147

Manufacturer Part Number 241798231

This 8-cube ice maker is used to create ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze until ice cubes are formed. Once the water has been frozen the cubes will be ejected from the mold in to the ice bucket. The ice maker will continue the process until the ice bucket has reached the limit. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Fixes these symptoms

Ice maker not making ice
Ice maker won’t dispense ice
Leaking
See more...

Installation Instructions

Juan from Miami, FL

Broken ice maker

Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. Read more...

Your Price

$4.65

CLAMP,SPRING

★★★★★

1 Review

PartSelect Number PS16224004

Manufacturer Part Number MBU64446301

The fan blade clamp, also known as a clamp spring, are for air conditioners. The clamp supports the fan blade on the motor shaft. When the motor is running, it signals the shaft to turn and rotate, but without the support of the clamp the motor shaft is unable to function properly. Refer to the manual provided by the manufacturer for installation instructions and accurate guidance. Remember to unplug your air conditioner from the power source as a safety precaution and wear work gloves while you perfrom this repair.

Your Price

$17.95

WASHER

★★★★★

1 Review

PartSelect Number PS12578732

Manufacturer Part Number W11236646

This part is located on the drum roller support shaft in your dryer appliance. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They are installed alongside the drum support rollers and idler pulleys. If you notice that your dryer is making an unusual sound it could be due to the washer becoming loose on the drum support. They help prevent the rollers and pulleys from bumping up against the brackets they are installed on. If you are replacing the rollers, we suggest you replace the washers at the same time.

Fixes these symptoms

Noisy
See more...

Installation Instructions

John from Tucson, AZ

worn out part

The repair was fairly easy. The most timely part of the repair was removing the twelve screws from the back panel to expose the repair. Read more...

Your Price

$20.88

Motor Clip

★★★★★

2 Reviews

PartSelect Number PS11757442

Manufacturer Part Number WPY015825

Sold individually.

Installation Instructions

Jeffrey from Bend, OR

Rumble noise and groaning on startup.

I found that I replaced more parts than I needed to fix fhis problem. The source of the rumble was the blower wheel connection to the motor, allowing the wheel to wobble (plastic wheel flat spot worn off over time, no firm lock to the motor shaft). But the dryer should be good for another 10 years!

Disconnect dryer from electrical outlet and exhaust.

Remove the back access plate to release the belt from the pulley. Remove the two screws at the bottom front of the dryer, rotate the front to release it at the top. Remove the wires from the door status switch. Remove the 4 nuts holding the drum support frame and pull straight out. Remove the drum. Remove the two bolts holding the thermostat cover (silver odd shaped metal plate at the front of the dryer). Remove the dryer blower cover plate by removing the 6 bolts holding it to the blower housing. Remember to remove the bolt holding the plate to the bottom of the dryer. Release the door status wire from the clips on the left side of the dryer and set the blower housing plate to the right, out of your way without removing the wires. Remove the blower wheel by removing the Circlip at the front of the shaft and then removing the shaft compression clip. Pull out the blower wheel and then remove the rear Circlip from the motor shaft. The back of the blower housing can be removed by removing the 4 bolts holding it to the motor support frame to make access easier but this may not be necessary. Release the 5 wires attached to the motor. Release the front and back motor clips. I used a large straightblade scerwdriver to press down and out on the end of the clips. Lift out the motor. Remove the rear pulley from the motor using an allen wrench and transfer it to the new motor. Set the new motor in the support frame, ensuring the lips of the vibration isolation rings are pointed down to slip over the frame and are not facing up towards the clips ( makes clip instalaltion much easier). Hook up the wires, following the color coding on the motor controller you are attaching to. Reinstall the blower back housing if removed, rear circlip, blower wheel, front circlip, shaft compression clip, blower housing front cover (Including the bolt to the dryer bottom) , reroute the door switch wire up the left side, reinstall the thermostat cover, reinstall the drum and belt, reinstall the drum front support frame (ensure the felt seals for the drum and the blower cover are properly aligned and seated correctly), hook up the door status wire when your set the front cover and install the 2 screws, reinstall the belt through the pulley and idler wheel (make sure the belt smooth side is against the drum) through the back access panel and reinstall the panel. Read more...

Fan Assembly,Axial – Part Number: 5900AR1173A

Your Price

$24.46

Fan Assembly,Axial

★★★★★

2 Reviews

PartSelect Number PS3528606

Manufacturer Part Number 5900AR1173A

The fan assembly or condenser fan blade fits on the motor shaft and circulates air over the condenser. This cools the refrigerant before it enters the evaporator. If the fan assembly in your room air conditioner is not operating properly, you will need to replace it with this part. This fan assembly has 5 blades and is approximately 14-1/2 inches in diameter. It is made of white plastic. You will need to open your air conditioner, and most likely remove it from the wall/window to complete this repair. Be sure to disconnect power to the unit before you begin this repair.