General Electric Wall Oven Lights and Bulbs

Your Price

$21.66

General Electric Wall Oven Halogen Lamp - 50W

★★★★★

15 Reviews

PartSelect Number PS2339783

Manufacturer Part Number WB08X10057

Lamp also known as light bulb. Sold individually.

Fixes these symptoms

Won’t turn on
See more...

Installation Instructions

Sharry from Lititz, PA

Microwave bulb was burnt out

It is easy to repair the burnt out bulb if one has the correct bulb. Your website is very user friendly and your service is great. I was not able to replace the bulb at this time because our RV is at the repair shop for some other matters. I am sure the installation of the new bulb will go smoothly. Thanks for asking. Sharry Kiehl Read more...

Your Price

$13.75

General Electric Wall Oven LAMP HALOGEN BULB G9

★★★★★

4 Reviews

PartSelect Number PS8754479

Manufacturer Part Number WB25T10102

Installation Instructions

George from PALM COAST, FL

A burnt out bulb

After opening the Oven door, I removed the glass cover to view and locate the bulb, at the inside, top front of the Oven. Removed the burnt out bulb by pulling it in a forward motion towards the front of the Oven, slid the new bulb into place and the Oven is again functional. Read more...

Videos!

Your Price

$28.94

General Electric Wall Oven Oven Light Housing

★★★★★

11 Reviews

PartSelect Number PS230438

Manufacturer Part Number WB08T10002

The light housing is also known as a lamp holder and is a part for the oven in your range. The function of this piece is to hold the bulb that will light up the inside of your oven. As per the manufacturer instructions, if your bulb has burnt out you must buy the bulb for this part locally. This light housing is roughly five inches high, with an outside diameter of roughly four inches by four inches. To install this part, you will need a Phillips screwdriver, a nut driver, and a pair of pliers.

Installation Instructions

Jack from Okmulgee, OK

Oven Lamp Holder Burned

removed two phillips screws. Unplugged electrical connections replaced unit from PartSelect. They sent holder cover and new bulb (surprise). Great store with great directions. Read more...

Your Price

$37.02

General Electric Wall Oven Halogen Bulb - 20W - 12V

★★★★★

12 Reviews

PartSelect Number PS951718

Manufacturer Part Number WB01X10239

This light bulb is a 12 Volt/20 Watt bi-pin base halogen lightbulb, meaning it emits a bright, white light which is similar to natural daylight and is inserted into its socket, as opposed to being rotated in. This bulb specifically is designed for use and compatible within various makes and models of home appliances, such as refrigerators, microwaves and ranges, and is sold individually. This halogen bulb can last up to 2000 hours and will begin to emit a yellow-ish tint or diminished brightness as it ages and deteriorates.

Installation Instructions

Edward from Averill Park, NY

Halogen bulb beneath microwave lighting the stovetop burned out after 9 mo.

Unscrewed the light cover beneath the microwave with a phillips head screwdriver. The bulb is very tiny and has 2 straight parallel prongs that slide into 2 small holes. Grab bulb from both sides with each hand firmly and slide STRAIGHT out (no twisting or pushing). Don't worry about breaking even though it may take a fair amount of pressure to pull out. New bulb arrived within a couple of days. Due to high shipping cost, suggest buying 2 or more bulbs at once. Bulb is often used as a kitchen night light so that is probably why I only got 9 months out of it. Read more...

Videos!

Your Price

$11.51

General Electric Wall Oven Oven Bulb Lens Cover - Glass

★★★★★

8 Reviews

PartSelect Number PS237483

Manufacturer Part Number WB25T10002

This part is the replacement oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover is rigid and protects the oven light bulb from being damaged. The main reason to replace the oven bulb lens cover is if it is cracked, damaged, or missing. Be sure that the lens cover is cool to the touch before you begin this repair. To remove the lens cover simply turn it counterclockwise until you can remove it. Replace it with a new cover and turn it clockwise to lock it into place. This is an OEM part sourced from the manufacturer, and it is sold individually.

Installation Instructions

Francis from LAKE ELSINORE, CA

broken light cover

twisted it in place Read more...

Your Price

$13.53

General Electric Wall Oven Light Cover

★★★★★

8 Reviews

PartSelect Number PS247415

Manufacturer Part Number WB36X192

This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. Disconnect power to your appliance before this repair. It is recommended to check the light bulb while the lens cover is removed in case it needs to be replaced. Be sure to remove all broken glass, if applicable, before installing new lens. This part is sourced directly from the genuine manufacturer, and is sold individually.

Installation Instructions

Edward from Ashland, MA

I Tried to remove Oven Light and got a spark that took out the Control Panel.

Oven light was easy - Snapped the Wire Bail, removed the Glass Protect and removed the buld. Installed new bulb, installed Glass Protect and snapped the Wire Bail. The Control Panel was a little harder and had to remove the 4 screws holding the metal Back Plate cover. I wrote down all the wire connections and then unplugged the wires. I took a 1/4 nutdriver and removed 4 screws holding Control panel in place and removed the Panel. The new control panel did not come with the Switch Face Plate so I removed the old one with a razor blade. The Switch Face Plate had plenty of adhessive so I just aligned the Face Plate with the Control Panel and seated it in place - thankfully it held firmly. I installed the Control Panel with Face Plate into the range and secured it with 4 screws using nutdriver. I plugged the wire connectors into the Control Panel and installed the Metal Back Plate to the range and secured it with 4 screws. Plugged the Range into the sockets and checked it for operation. Everything worked Ok including the new oven light. Read more...

Your Price

$20.14

General Electric Wall Oven Halogen Lamp - 35 Watt

★★★★★

3 Reviews

PartSelect Number PS230456

Manufacturer Part Number WB08T10023

This halogen lamp bulb is a genuine OEM replacement part for your oven. If the light has burned out in your oven, replace it with this part. This is a 35 watt bulb. Replacing this bulb is fairly easy but will require pulling the oven out from the wall. Make sure to shut off power to the unit before beginning this repair.

Installation Instructions

Dave from DANDRIDGE, TN

Oven light burned out

Wait until oven is cold. Turn off power to the oven at the breaker panel (confirm: clock will be off). Open oven door. Remove upper rack. Unscrew glass cover over lamp and socket (it only turns one direction and may be tight). Slide cover off lamp socket. Remove old lamp - pull straight down. Install replacement lamp. Lamp pins line up front to back. Do not touch the lamp - use latex gloves. Make sure the lamp is fully pushed into its socket. Replace the glass cover by centering it on the socket with glass retaining tabs close to the matching areas on the metal socket. Take care not to damage the lamp. Turn the cover to lock in place. Make sure it is locked. Replace oven rack. Turn the power back on. Read more...

Your Price

$14.57

General Electric Wall Oven LAMP HALOGEN 20W

PartSelect Number PS1018917

Manufacturer Part Number WB25T10064

Your Price

$9.49

General Electric Wall Oven Snap-In Lens

★★★★★

5 Reviews

PartSelect Number PS237500

Manufacturer Part Number WB25T10022

Installation Instructions

Steven from GOSHEN, IN

The heat setting numbers were worn off and missing due to cleaning this cover with something abrasive.

Removed the heat setting knobs which then reveal the 4 plastic retainers which are easily unthreaded using a Crescent wrench. Then the overlay panel simply lifts off and the new one placed on and the retainers are threaded back on.
It's a very easy fix. Read more...