Models
>
CAV2004AJW
CAV2004AJW Magic Chef Washer - Overview
Sections of the CAV2004AJW
[Viewing 9 of 9]
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Magic Chef Washer")
Manuals & Care Guides for CAV2004AJW
Click to downloadKeep searches simple, eg. "belt" or "pump".
Drive Belt - 51 inches long
PartSelect #: PS11738882
Manufacturer #: WP21352320
This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suf...
$10.98
In Stock
Lid Hinge
PartSelect #: PS11741780
Manufacturer #: WP35-2044
The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to replace the lid hin...
$11.18
In Stock
Lid Hinge Pin
PartSelect #: PS11741781
Manufacturer #: WP35-2045
This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plast...
$22.28
In Stock
Snubber Ring
PartSelect #: PS11738845
Manufacturer #: WP21002026
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
$13.11
In Stock
Washer Drain Pump
PartSelect #: PS11741803
Manufacturer #: WP35-6780
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and s...
$120.13
In Stock
Transmission Pulley and Bearing Kit
PartSelect #: PS2003651
Manufacturer #: 12002213
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
$69.83
In Stock
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Suspension Springs - Kit of 6
PartSelect #: PS2004049
Manufacturer #: 12002773
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
$68.55
In Stock
Screw
PartSelect #: PS11742755
Manufacturer #: WP489483
This screw is sold individually.
$13.09
In Stock
Water Valve - 60/40
PartSelect #: PS11738838
Manufacturer #: WP21001932
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
$123.10
In Stock
Hose Clamp
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$11.10
In Stock
Questions And Answers for CAV2004AJW
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the CAV2004AJW
[Viewing 11 of 11]Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
One of the plastic hinge pins brroke
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
Parts Used:
-
Allen from North Little Rock, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
512 of 515 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump was making a grinding noise
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A
... Read more
small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
Read less
Parts Used:
-
Ranse from Layton, UT
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Socket set
295 of 317 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
EXCESSIVE Banging, shaking and squeaking while on Spin Cycle
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drai ... Read more n into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drai ... Read more n into small container, about 4 cups of water will come out.
5)Remove the 6 suspension Springs.
6)Place two large towels next to washer and tip machine onto its side slowly.
7)Remove drive belt from bottom, and slide out wash tub assembly thru top opening, be Careful not to damage large Plastic drive pulley on bottom of tub.
8)With tub upside-down, remove drive pully small plastic cover in center, remove E-Clip and remove pulley.
9)Slowly loosen snubber ring retaining bolts a few turns, DO NOT Remove, just loosen enough until snubber is free to move around.
10)Remove snubber ring by walking it around the retaining ring and install new snubber.
11) Clean machine cabinet and clean machine base where snubber touches with alcohol or Windex.
12) Reassemble in reverse order and Do Not Forget to reattach the small clear Water level sensing HOSE to the tub before closing the top.
13)Place Drive Belt onto the 2 small pulleys First, then slowly turn large pulley while walking belt onto it.
14)Reconnect machine to utilities and test run on small load to ensure no leaks and propper operation.
15)Enjoy Quiet free operation once again :)
Read less
Parts Used:
-
robert from simpsonville, SC
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers
127 of 137 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!