This gear is used to power your stand mixer. It is attached to the planetary shaft. The gear can become stripped over time or accumulate grease. You may need to replace other mechanical parts at the s...
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the ac...
This bearing comes equipped with two washers and is used on stand mixers.
$15.73
In Stock
Questions And Answers for 4KP26M1XLC5
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Akhtar
December 19, 2023
Grease leaking from planetary shaft. Need instructions how to fix.
Thanks a lot in advance.
For model number 4KP26M1XLC5
Hi Akhtar, thank you for reaching out. We have found the instructions to repair the grease leaking. These may not be of the same model but will help you to fix it. You may need to follow these steps:
1. First, take off the back cover by removing the screw. With the cover off, pull the power cord out of the slot.
2. Use a screwdriver to pry off the drip ring.
3. Use a punch to drive the dowel pin out of the shaft.
4. Pry off the planetary.
5. Remove the upper housing by removing the screws around the planetary gear and remove the screws on the bottom of the housing.
6. Use something to scrape out the old grease as much as you can.
7. Pull out the gasket, center gear, hub gear, and shaft, then separate the worm gear assembly by removing the screws that hold it on.
8. Wipe all the parts down with an old rag to remove as much grease as possible, then soak or scrub in the degreaser.
9. Pack everything in fresh grease. Try to add the same amount as you removed. Rotate the gears by hand to make sure the grease is distributed everywhere and things are moving smoothly, the hub gear can be greased and installed in the upper housing. Also pack grease around the motor gear in the upper housing. Add some grease to the planetary gear as well.
10. Place all the parts by following the same steps backward.
We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
removed metal strap around motor housing then remove the 4 screws holding top motor cover on, then removed the 4 screws that hold gear cover in place, remove long gear that is driven by the motor gear, then with ring pliers remove ring off long drive shaft and lift off worm gears. once all gears are removed --removed all the old grease (
... Read moredo this to get all the metal shavings out from the failed gear) repace the grease in the gear housing and reassemble in reverse order
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them
... Read more, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plasti
... Read morec gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.