Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Oven had delayed relite after reaching temp blew oven door open
Replaced gas control valve problem solved, all went well
robert from CLINTON, MD
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Wrench set
2 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
5 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Steve
November 29, 2017
I noticed that when i turned on my oven, after a few minuets it did not light so, i "tapped" the gas valve and it light. So i'm assuming the valve is going bad? Now i have turned on the oven 2 other times and it seems to take a little longer to light but, it did come on. Now i also noticed that the vent fan shuts off immediately when i turn off the oven, not staying on to cool down. Could this also be related to the valve going bad? Thanks.
For model number PGS908SEP3SS
Hi Steve,
Thank you for your question. If your igniter is not lighting, there are some parts that you will need to check to see which one is causing the issue. You will need to check the top burner spark igniter, the oven igniter, the burner heads, the top electrode mounting clip and the gas control valve. I hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Link
February 19, 2018
Per heat takes 35 min to 40 min. To get to 425. Igniter turns red and gas is ignited in less than 40 sec. Burner seems to be working all blue flames and even. Flame maybe slightly low but all are working.
For model number JGSP48SH4SS
Hi Link, Thank you for the question. I suggest testing the Temperature Sensor, PartSelect Number PS10059162.Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!
Was this helpful?
Thank you for voting!
Anya
November 16, 2018
What parts are required to convert oven from gas to propane? Please provide list of needed parts & manual if possible. Thanks!!
For model number JGSP28SEN3SS
Hi Anya, thank you for your question. I have listed the orifices for your burners down below for you. Unfortunately there is no manual for how to replace these parts. However you just have to turn off the gas to the appliance and unscrew the old orifices and replace them with the new ones. For your regulator, there is already an orifice on the inside. All you have to do is flip that part around to change it to LP. I hope that helps. Good luck with your repair.
Good evening. My gas range worked great until i had to remove the lower grill. When i forcefully got it to get out, the gas oven and broiler would not work. The stove top however works fine. Replaced igniter for oven last year. I don't think that is the problem, as th broiler igniter works fine also. Leaning towards gas valve. What do you think?
For model number Jgsp48sh2ss
Hello Mark, thank you for inquiring. Yes, this is most likely due to the Gas Control Valve, part number PS953461 for your model. You may also want to consider the Oven Control, part number PS2374110. Good luck with your repair!
Was this helpful?
Thank you for voting!
Joe
July 31, 2017
Oven igniter glows red in lower portion of oven but doesn't open gas valve to ignite. Works in broil not bake. What part do i neef
For model number Jgs968sh3ss
Hi Joe,
Thank you for the great question! The igniter can glow but might be to weak to open the valve. Here is a link to our How To Fix A Gas Range or Stove Igniter That Won't Light page.
http://www.partselect.com/Repair/Range-Stove-Oven/Gas-Igniter-Will-Not-Light/
Hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
