Make sure you haven't got the discount earlier.
![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
GROMMET & FILL TUBE D WR02X11258
Fits your ZISS420DMB Refrigerator!
★★★★★
★★★★★
Rated by 1 customer
A Bit Difficult
30 - 60 mins
Ratings submitted by customers like you who bought this part.
Fits your ZISS420DMB Refrigerator!
PartSelect Number PS652419
Manufacturer Part Number WR02X11258
Manufactured by
GE
Troubleshooting
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric.
Part# WR02X11258 replaces these:
WR17X6332, WR2X11258
Customer Reviews
Average Rating:
1 Review
★★★★★
★★★★★
3.0
Filter By Rating:
-
5 Stars
-
4 Stars
-
3 Stars
-
2 Stars
-
1 Star
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Christopher T - September 23, 2019
Verified Purchase
Part worked after modification
The parts arrived as scheduled. The replacements parts were not the same size as the originals so modifying the grommet to shorten it so it would fit was necessary. The new fill tube was metal compared to the plastic original and was also longer than the original. It was easier to reuse the original plastic fill tube (it was in good condition) than trim the length of the new metal fill tube. But with appropriate tools the new metal fill tube could have been shortened to match the length of the original for a good fit.
- < Prev
- 1
- Next >
Back to Top
Customer Repair Stories
Average Repair Rating: 2.8 / 5.0, 1 reviews.
What's this?
Sort by:
- < Prev
- 1
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
The point of connection between the ice maker fill tube assembly and the poly tubing was leaking and water was freezing inside the fill tube and grommet.
1. The fill tube assembly is located on the left side of the compressor compartment on top of the refrigerator toward the back of the unit.
2. Remove the front grill from the compressor section and turn off power to the refrigerator.
3. In the freezer section, remove the ice maker cover, ice holding/feed tray, and the ice maker ... Read more assembly.
4. It was necessary to use a small hair dryer to unfreeze ice inside and around the fill tube so that the fill tube could be pulled down from the grommet.
5. The grommet, which is located on top of the freezer unit next to the compressor, having been in place for many years, was difficult to remove both because of the difficulty of reaching the grommet in the narrow space between the compressor housing and the outside body of the refrigerator and the grommet fitting so snugly into the mounting hole.
6. To remove the grommet, I carefully used a set of small plastic pry tools (available at an auto parts or hardware store) to slowly unseat the grommet from the refrigerator and then used a twisting motion while pulling up on the grommet to remove it from the housing.
7. Clean around the hole in the freezer housing carefully.
8. For my model refrigerator, the new grommet piece is slightly longer than the original piece, and while the original fill tube is plastic, the replacement fill tube is made from metal and is slightly longer than the original fill tube.
9. Due to the different sizes of the new parts, it was necessary to shorten the length of the new grommet so that it would seat properly into the hole in the compartment. I also had to reuse the old plastic fill tube so that the fill tube would properly fit inside the ice maker assembly. It is probably possible to trim the metal fill tube with an appropriate cutting tool if the old tube cannot be reused.
10. If you are going to trim the new unit, carefully measure the old grommet and trim the new grommet to match the size of the original, then insert the new grommet into the hole in the upper cabinet section. The fill tube can than be inserted into the grommet from inside the freezer compartment by sliding the fill tube into the hold inside the freezer compartment and seating it by feel into the grommet. However it is also apparently possible to fit the fill tube into the grommet first and then insert the fill tube and grommet from the top of the refrigerator where the hold inside the compressor space is located.
11. If replacing the poly tubing between the water valve assembly and the grommet (a good idea if the tubing is old), it is simpler to attach new poly tubing into the grommet before placing the grommet into the mounting hole. A small hose clamp can be used as well to secure the tubing in the grommet attachment point.
12. Mount the ice maker in the freezer compartment making sure the fill tube sits inside the plastic piece at the back of the ice maker that collects the water from the fill tube.
13. Replace the ice collection/feed component.
14. Replace the ice maker cover.
15. Turn on the unit and test the ice maker to ensure there are no leaks in the new parts.
2. Remove the front grill from the compressor section and turn off power to the refrigerator.
3. In the freezer section, remove the ice maker cover, ice holding/feed tray, and the ice maker ... Read more assembly.
4. It was necessary to use a small hair dryer to unfreeze ice inside and around the fill tube so that the fill tube could be pulled down from the grommet.
5. The grommet, which is located on top of the freezer unit next to the compressor, having been in place for many years, was difficult to remove both because of the difficulty of reaching the grommet in the narrow space between the compressor housing and the outside body of the refrigerator and the grommet fitting so snugly into the mounting hole.
6. To remove the grommet, I carefully used a set of small plastic pry tools (available at an auto parts or hardware store) to slowly unseat the grommet from the refrigerator and then used a twisting motion while pulling up on the grommet to remove it from the housing.
7. Clean around the hole in the freezer housing carefully.
8. For my model refrigerator, the new grommet piece is slightly longer than the original piece, and while the original fill tube is plastic, the replacement fill tube is made from metal and is slightly longer than the original fill tube.
9. Due to the different sizes of the new parts, it was necessary to shorten the length of the new grommet so that it would seat properly into the hole in the compartment. I also had to reuse the old plastic fill tube so that the fill tube would properly fit inside the ice maker assembly. It is probably possible to trim the metal fill tube with an appropriate cutting tool if the old tube cannot be reused.
10. If you are going to trim the new unit, carefully measure the old grommet and trim the new grommet to match the size of the original, then insert the new grommet into the hole in the upper cabinet section. The fill tube can than be inserted into the grommet from inside the freezer compartment by sliding the fill tube into the hold inside the freezer compartment and seating it by feel into the grommet. However it is also apparently possible to fit the fill tube into the grommet first and then insert the fill tube and grommet from the top of the refrigerator where the hold inside the compressor space is located.
11. If replacing the poly tubing between the water valve assembly and the grommet (a good idea if the tubing is old), it is simpler to attach new poly tubing into the grommet before placing the grommet into the mounting hole. A small hose clamp can be used as well to secure the tubing in the grommet attachment point.
12. Mount the ice maker in the freezer compartment making sure the fill tube sits inside the plastic piece at the back of the ice maker that collects the water from the fill tube.
13. Replace the ice collection/feed component.
14. Replace the ice maker cover.
15. Turn on the unit and test the ice maker to ensure there are no leaks in the new parts.
Read less
-
Christopher from APOPKA, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Back to Top
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Back to Top
You May Also Need
?
![FILL TUBE HTR 10W – Part Number: WR51X10056](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/assets/images/noimage_N.jpg)
![COVER WATER LINE – Part Number: WR17X13124](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/8768038-1-N-GE-WR17X13124-COVER-WATER-LINE.jpg)
![Produce Preserver Filter – Part Number: W10346771A](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/3503014-1-N-Whirlpool-W10346771A-Produce-Preserver-Filter.jpg)
![Affresh Washing Machine Cleaner - 3 pack – Part Number: W10135699](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/1960673-1-N-Whirlpool-W10135699-Affresh-Washing-Machine-Cleaner-3-pack.jpg)
![Affresh Dishwasher Cleaner Tablets - 6 – Part Number: W10549851](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/12345667-1-N-Whirlpool-W10549851-Affresh-Dishwasher-Cleaner-Tablets-6.jpg)
![Affresh Cleaner – Part Number: W10282479](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/2367638-1-N-Whirlpool-W10282479-Affresh-Cleaner.jpg)
![Cooktop Cleaner – Part Number: W10355051](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/3492527-1-N-Whirlpool-W10355051-Cooktop-Cleaner.jpg)
![Affresh Ice Machine Cleaner – Part Number: W11179302](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/12583750-1-N-Whirlpool-W11179302-Affresh-Ice-Machine-Cleaner.jpg)
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS652419
Manufacturer Part Number: WR02X11258
Manufacturer Part Number: WR02X11258
Brand
Model Number
Description
Back to Top
![Customer Service Representative](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/images/csr-partdetail.jpg)
GROMMET & FILL TUBE D
$
51.65
Special Order
✖
Stock Status
In Stock
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.