Dual Inlet Water Valve - 120V 60Hz 218832401

removed dual inlet solenoid and replaced. Replacing this solenoid fixed the problem totally.

Pulled out the ref.from the wall,turned off the water,removed the dual water valve,replaced it with the new one ,turned the water back on,every thing worked greatl,be sure to un plug the appliance while making repairs.

Found that that ice maker was working mechanically and electrically but was not receiving water to the ice maker. I found that the dual solenoid valve was not sending water to the ice maker when I asked for water so I ordered a new dual solenoid and this fixed the problem,however I also found the water feed tube was frozen and had to take it off an thaw it out. Now the ice maker and water dispenser is working great.

remove solenoid and lines and replace new one every thing work fine

Jonnine's husband did the repair - At first, I was stumped on the cause of the problem because I thought because I did get some ice, the pump (valve) must be working. But after pulling the dust cover back off the bottom of the fridge, I removed the dual valve. I had my wife operate the switch in the door for water and I could tell that it wasn't activating the valve at all. Ordered the valve, took 30-45 minutes to put it on. Worked like a charm. Full ice bucket now and water through the door again. Easy install.

I started by shutting off water supply and unplugged refrigerator. Then using a nutdriver removed back lower panel exposing the dual inlet water valve on the left side which was held in place with one bolt. After unbolting the valve you can pull the entire assembly out enough to remove the three water connections. The instructions suggest cutting of about 1/2" off of the two discharge lines to provide a better connection to the new valve. The entire process was very simple. The price of the part was a small fraction of the new refrigerator my wife was threatening to buy if I did not get her ice maker working again. Thanks for another great repair experience!

Easy repair, matched parts from this web-site, removed several screws for each valve assy, installed each item, had water & ice !!!!! Both items $90 w shipping, we went to dinner with the money saved from not calling some a tech to repace them east items.

I followed all the usual suggestions about changing the water filter and disconnecting the exterior copper line and testing it to make sure flow was steady. I then got ambitious and diconnected and tested the flow of water through each of the refrigerator's interior valves. Isolating my problem inside the dual valve that regulates feed into the water dispenser and icemaker I was able to clear out the blockage with a small dustbuster air cannister but reassmbling the valves somehow caused the valve to no longer function right so I ordered a replacement valve and had it all reconnected in five minutes once the part arrived. A simple repair to avoid a very costly replacement! Partselect has now been used by me to repair my oven, refrigerator (twice) and microwave. A pretty good alternative to replacing an appliance if you are willing to try your own repair.

The part’s picture on the site was not identical to the part delivered, but the function was essentially the same. It had different connectors to the outgoing tubes and a slightly different method of attachment to the refrigerator (it required 1 additional skew - not included). After verifying the part would still work, I shut off the water. Then I disconnected the two outgoing tubes. Made sure I had bucket handy to handle excess water. Then I removed the part using an adjustable wrench (1 screw) and then detached the incoming tube. Attached the incoming tube to the new part and then remounted (2 screws). And then I attached the two outgoing tubes and turned on the water. It works great and I have no plumbing experience.

I order part # PS429001 dual inlet water valve located in bottom left corner of refridge on monday it arrived nest day.I then shut off water source and disconnected refridge.
I removed back bottom panel { 5screws} and then i removed
water valve {1 screw} I unplugged electrical wires and water feed lines from valve.You have to pull hard on feed lines to remove. I installed new valve, connected wires,
i had to clip off about 1/2" of feed line ends for a tighter fit on new valve. I reinstalled back panel. I plugged in refridge turned on water,and presto i'm getting
fast water again from the dispenser. P.S. I also took the time to vacumm around compressor and fan.
thanks PARTSELECT.