Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Terry W - February 20, 2021
Verified Purchase
It worked; I had to wire it up differently for my kenmore
The wires on the thermistor were fried. Apparently, the thermistor failed as it was burnt/smoked. It was difficult to remove the white plastic from the circuit board holder. One removed wire went down underneath the dishwasher; instructions left it hanging; also had the board connection hanging so I checked with an inline amp meter between the two hanging wires and got 250mA as the washer lit up. So I tied these together and all was good.
I read the instructions and what I did was different. I lucked out !! 4 stars becasue instructions do not address the two hanging wires. Need to include a wirenut.
★★★★★
★★★★★
Sean A - April 20, 2020
Verified Purchase
Matched exactly and worked az supposed too
The part arrived asap and from this sites installation video and most common part replaced percentage it was very simple to install.
★★★★★
★★★★★
Candice C - November 18, 2019
Verified Purchase
Simple repair.
Fast shipping!
★★★★★
★★★★★
George K - May 28, 2019
Verified Purchase
Easy repair, great instructions online
Perfect part. Worked as described. The online video showing how to replace it was excellent.
★★★★★
★★★★★
TIM S - May 12, 2019
Verified Purchase
Easy install
Part came well packaged and with good instructions. It was easy and a quick install, was back up and washing in few min.
★★★★★
★★★★★
Laura W - April 29, 2019
Verified Purchase
Working good
Part was what I needed works great I’m pleased with the time it took get to me and will continue to purchase from you again thanks
★★★★★
★★★★★
Dennis K - April 25, 2019
Verified Purchase
Worth a shot
My dishwasher quit working, lost power, when the motor kicked in. Replacing the thermal fuse was a relatively inexpensive try to get it working. The dishwasher was over 18 years old and not worth spending a lot of money on. Unfortunately, it turned out that wasn't the problem so I replaced the dishwasher. I received the thermal fuse quickly and in good condition. It just wasn't the problem.
★★★★★
★★★★★
Joseph K - September 23, 2018
Verified Purchase
Thermo fuse
Recieved part in 24hrs of ordering. Was in good condition up on delivery. Installed and fixed the problem. This is my second time I have purchased parts and each time was very satisfied. If I ever need parts again will definitely use your service again
★★★★★
★★★★★
THOMAS L - July 27, 2018
Verified Purchase
PERFECT PART
ALL WAS FINE WITH MY PART FOR THE REPAIR. ONLY GRIPE I WOULD HAVE IS THE LENGTH OF TIME FOR SHIPPING,,10 DAYS.
★★★★★
★★★★★
John B - June 5, 2018
Verified Purchase
Not very hard, Seems like this is the fix for your not turning on dishwasher
I made the mistake of trying to out smart everyone else when my used dishwasher wouldn't turn on and ordered the latch assembly first after inspecting the fuse and thinking it looked good and not testing it. The latch came and nothing happened. I finally decided to try the fuse and, bam turned on. The only thing that tripped me up was pushing the metal tab out of the black plastic block. I had to watch the video a few times to see that he pushes the metal piece from in between the plastic block and the metal piece, not pushing "inside' of the metal piece... if that makes any sense to anyone. Thanks Parts Select!
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 4.2 / 5.0, 4 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No power to dishwasher.
Unplug the dishwasher. Simply removed 8 screws on the inside of the door, removed the interior door panel. Next popped of the plastic protective electrical panel cover. Locate the Thermal fuse that had simple instructions provided. Removed the fuse and replaced the harness. Put everything back together. Plugged dishwasher back into electr
... Read moreical outlet...Dishwasher resumed with the cycle that the dishwasher was in when the fuse blew. Simple, Fast AND Reliable!!!
Read less
Brad from Woodbury, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
36 of 43 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dishwasher did not completed the drying cicle. heated dry button blinking
I just changed all parts that could make any effect in temperature control. even the thermal fuse. this was easy,looking in details all the drawings you have in your page. so I pulled out the dishwasher changed the parts and ready!! it work great now . thanks for your guide and help.
The machine just quit in the middle of a cycle and there were no lights on the control panel
There were eight of the star head screws to remove to take the front off the dishwasher, then just followed the instructions that came with the part, which was a thermal fuse and the new wiring that accompanied the fuse in the order. The hardest part was getting the old wire out of the harness with the other three, but once I figured that
... Read more out just slid the new wire into place and made the connections. I reinserted the screws, turned the power on and knock on wood shes still working.
Read less
Ronald from Garland, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
30 of 39 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Touch pad on dishwasher dead
1. Remove the two screws that attach the bottom cover. 2. Remove the 2 screws that attach the door outer cover. 3. Remove the 8 screws that attache the door inner cover. 4. Remove the plastic cover over the electronic controller. 5. Remove the two connections to the thermal fuse. 6. Remove the thermal fuse.
... Read more>7. Install the new thermal fuse. Reverse the above steps.
Read less
Jeff from Boaz, KY
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
113 of 132 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
6 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
November 18, 2017
When we push any button the light comes on for that selection, but when we the push start button it will not start the dishwasher. Any suggestions?
For model number 66515762000
Hello Dan,
The thermal fuse and harness should be tested with a multimeter for continuity and replaced if it is not showing continuity, as that is the most common reason for the dishwasher not starting.
It is also worth testing the door switch (part number PS358749) for continuity and replacing it if it is not showing continuity, as that can prevent the dishwasher from starting as well.
Only if the prior two parts are testing for continuity should consider replacing the electronic control board itself, part number PS11746115.
I hope this helps.
Replaced the fuse and it worked and finished cycle. The second wash it stopped again. Got another fuse and it worked for half of the cycle. What would cause a thermal fuse to continue to blow?
For model number DU945PWPQ0
Hi Mary Beth, Thank you for the question. When changing the fuse always use a new wiring harness.If the harness is not changed it will blow the fuse again. Hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Richard
September 29, 2017
Kenmore dishwasher......select option on control panel....push on button....immediately shuts off panel. is this the thermal fuse problem? or control panel?
For model number 66515822000
Hi Richard, Thank you for the question. In this case I suggest replacing the Electronic Control Board,PartSelect Number PS11746115. The thermal fuse would need to be replaced if the appliance worked but had no display. Hope this helps!
The only lights that come on are cancel, and heavy and normal. The heavy and normal come on at times and blink when i press and hold cancel for a few seconds. Then when i press cancel again they all go off. I press normal then both normal and heavy come on and stay lit (doesn't happen when just heavy is pressed). When i press start the lights go off. Press and hold cancel and heavy and normal start blinking, and when i let go they all stay lit. Press start and the cancel button stays lit and the heavy and normal turn off. Then hold cancel and the heavy and normal start blinking again, as in the second sentence. I replaced the main control board with a new one and get the exact same sequence of events.
For model number DU945PWSQ0
Hello David, Thank you for your inquiry. If you've already replaced the main control board, I would check the control panel and touchpad assembly. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jim
May 13, 2019
Unit shows lights on control panel push button for normal wash hear click to start but won't.Check thermal fuse it is black on top blown,can fuse just blow or possible thermostat cause this, so i should replace that also
For model number DU940QWDQ6
Hello Jim, Thank you for the question. We suggest replacing both parts at the same time. Normally if one blows it is an indication there is a issue with the other. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Mary
December 8, 2017
My husband replaced fuse a few months ago. It quick working again and now replaced a fuse and it worked for one load but second load it stopped before dispensing detergent. Water not drained. He didn’t replace the electrical that came with it. Could that be the problem?
For model number DU945PWPQO
Hello Mary, Thank you for the question. Yes, the electrical should also be replaced for proper operation of the fuse. Good luck with the repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
