Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Louis
February 8, 2020
Trouble shooting - the cooling light stays on and the drying light blinks. I have replaced a drum roller and drive belt, when put back together and started it up the cooling light stays on and the drying light blinks. I than replace the dryer thermistor temperature sensor and high-limit thermostat sensors and didn't resolve the issue. Please help
For model number DLG2522W
Hello and thank you for writing.
We suggest to try a hard reset:
Go to your breaker box and shut the breakers for your unit off, wait 5 minutes and then turn the breaker to on again. That should hopefully clear this problem.
If this does not fix this problem then your sensor PS3529161 or main control board might be faulty and possibly needs to be replaced. We hope this helps. Please contact us anytime.
And new LG dryer. Installed propane orifice adjusted gas valve. Burner lights for 30 seconds then shuts off as if not detecting flame.
For model number DLGX7801VE
Hello James , Thank you for the question. We suggest testing the Igniter. It may have been bumped while converting to LP. On a good igniter, there should be between 40 & 400 OHMS. A bad igniter will show no resistance or continuity. We hope this helps!
As stated prior to this the dryer ignites and burns for about 30 seconds then burner shuts off. You suggested I test igniter. I did and it tests good. As I stated it ignites and Burns for about 30 seconds and shuts off. I don’t understand your suggestion to test igniter as I stated ignition isn’t the problem it ignites fine but will not stay lit
For model number DLGX7801VE
Hello James, Thank you for the question. A weak igniter may light but not have enough power to stay lit or keep the valve open. This issue can also be caused by too much heat. You can check the vent and inside the cabinet for any lint build up preventing a good air flow. A dryer must be able to blow the moisture out of the dryer. If it can’t due to a clogged vent or poor air flow, the flame will go out. You can also test the Flame Sensor, Thermostats and Thermistor. We hope this helps!
My LG DLG9588WM gas dryer does not heat. I’ve replaced the thermistor, blower thermostat, high limit thermostat (with the reset button), and the burner igniter. Still no heat. Both thermostats have the same size wire connector. Does it matter if they are fazed correctly? I couldn’t locate any positive or negative symbols on the original or replacement parts. My lint trap and exhaust tubing are free and clear. There’s two other parts listed that only have a 1% needed for this condition that I have not replaced. That would be the gas valve assembly, and the sensor assembly. I haven’t replaced the moisture sensor either. I really enjoy your website and have found great help with the videos. A few years ago I was able to repair my dishwasher with help from videos and parts purchased from you.
For model number LG DLG9588WM
Hello Jon, Thank you for your inquiry. You can test the parts with a multimeter to see if one of them is the issue. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Gas Dryer not getting hot
I noticed the flame would start, then quit after about 15 seconds. I checked the flame detector, and found the lenze cracked. I replaced it, and it's as good as gold.
It looked like a hard job to take the drum out to get at the part. But the top was off with 3 screws, the front about 6 I think. Then the front frame, only 4 screws. I think setting the belt tentioner was the hardest thing to do.
Done in 45 minutes, both the job, then the next load of laundry.
The Fix App makes it easy to manage all your stuff in one place. Just snap a photo and we'll find and store your user manuals, receipts, and product information in one easy-to-find place!
"Like magic. I took a picture of the model number on my refrigerator, and the app identified it right away … Very convenient. I'm impressed." ★★★★★ - Clever Jeff
