Quick Question!

Have you ever purchased from PartSelect.com before?

238567-1-S-GE-WB27T10267        -Electronic Oven Control
238567-1-S-GE-WB27T10267        -Electronic Oven Control 238567-2-S-GE-WB27T10267        -Electronic Oven Control https://www.partselect.com/Schematics/GE/00007254i01.gif

Electronic Oven Control

Your Price

PartSelect Number PS238567
Manufacturer Part Number WB27T10267
Manufactured by GE

The wiring could be different than the original and might need to be installed by an appliance repair person.

This part works with the following brands: Kenmore, General Electric.

This part works with the following products: Range.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.1 / 5.0, 2 reviews What's this?
1-2 of 2

6 of 6 people found this instruction helpful

Parts Used:
  • Electronic Oven Control
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Walter from Idaho Springs, CO

Fried out oven controller electric circuit board

Removed side retainer pieces, screws above and below accessed by opening oven door and straight down on oven top. Then two back screws to free controller. Let console fall forward. Remove four screws holding oven circuit board, replace with new board, then carefully move one wire at a time from old board to new board. Used magnifying glass to verify labeling on tiny print on new board. Needed pliers to remove tight pin fittings. Need to focus and not forget labeling switching wires.

Although I thought I was done, it turned out later that the oven wasn't coming on. After taking it apart again, it seemed strange no wire was hooked to the oven prong on the circuit board. I tried switching a few and thank god nothing bad happened. I then studied the directions. There were mentions of wires I didn't have hooking to various places including the oven relay. So I wasn't sure what to do. The broiler has worked so I unhooked the broiler wire and fastened it to bake prong. The oven now worked. I clipped the unnecessary female prong wire from the old ground connected and spliced it into the broiler wire and then hooked it to the oven prong. The oven and broiler prongs are effectively hooked in parallel now. I tested it and the thermostat and shutoff worked properly with both the oven and broiler working.

All done after reassembly.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
  • Electronic Oven Control
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Gary from Buffalo, NY

Getting codes from old unit, no nothing,just blinking

first turned off the gas supply, second turned off breaker for that line,third removed 3 screws from each side of panel & end caps. Used bubble wrap to lower panel down to remove old part, changed one wire at a time to keep it right,next removed 4 screws to replace with new unit, screwed new one in place, put back on the side caps turned on the power & gas. The new part works just fine,back to working again. I just did this today, Thank You very much for the right part and great shipping time, I will get part from you again. Thanks for the fast service and the right part again. Easy as pie. Gary

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-2 of 2

Model Cross Reference

This part works with the following models:

PartSelect Number: PS238567
Manufacturer Part Number: WB27T10267
Brand Model Number Description
General ElectricJGRP17BEW1BBRange - Gas
General ElectricJGRP17BEW2BBRange - Gas
General ElectricJGRP17BEW4BBRange - Gas
General ElectricJGRP17BEW5BBRange - Gas
General ElectricJGRP17BEW6BBRange - Gas
General ElectricJGRP17WEW1WWRange - Gas
General ElectricJGRP17WEW2WWRange - Gas
General ElectricJGRP17WEW4WWRange - Gas
General ElectricJGRP17WEW5WWRange - Gas
General ElectricJGRP17WEW6WWRange - Gas