This is a replacement cooktop mounting screw, used to secure the burner. If you are missing that screw on your range, this is the part to replace it. This screw is about a half an inch in length and is sold individually. It is an OEM part sourced directly from the manufacturer.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Range, Cooktop.
This part works with the following products:
General Electric, Kenmore, Hotpoint.
Part# WB01K10008 replaces these:
AP3155894, 768973
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
1.0
Filter By Rating:
5 Stars
0
4 Stars
0
3 Stars
0
2 Stars
0
1 Star
1
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Edward B - January 30, 2019
Verified Purchase
Very complex, often impossible repair, especially on an old range
The problem in attempting to remove and replace any of the 12 stovetop (aka-cooktop) mounting screws is that you can easily twist off the head if it gives even mild resistance to being unscrewed, they are then impossible to repair as the screw is too tiny and far too long to allow any broken screw removal tool to work and remove the broken screw. if the screw head shows ANY sign of rusting, do not even try to remove it, as these screws do more than hold down the cooktop, they secure each of the four burners in place. It is best to just avoid touching these screws on a stove more than a few years old. I ended up replacing the stove when I tried to replace these screws.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.5 / 5.0, 2 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
No burner
I just put everything on it and lighted match and problem solved! Easy fix!
18 year old gas range, just replaced oven igniter, and tried repairing burner igniter
I replaced the oven igniter, discovered the floor of the oven had rusted through, so I replaced that as well. The burner on top of the stove would not light as it was designed, and because the 12 screws that hold the range top and burners in place were rusted in place I ended up buying a new range because removing the screws on the burne
... Read morers proved impossible, even when I tried to drill them out with a lefthanded screw removal tool. I should have just kept lighting the burner that would not light, with a match. That was a repair too far, that forced me to buy a new GE Range and throw this one in the trash. The igniter, oven floor replacement was easy. The burner igniter after 18 years proved impossible. .I installed the 18 yr. old burner grates on the new range, but the drip pans would not fit the new stove. New GE Range instructions were near useless. Do Not trust them, especially the Orifice change details NG to LPG.
Ask our experts a question about this part and we'll get back to you as soon as possible!
1 question answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sylvia
March 29, 2023
Screws on rapid boil won't budge, need to replace ignitor
For model number jgb908sek4ss
Hi Sylvia, thank you for reaching out. Based on our research, you may use a rust buster to overcome the resistance of the screw, part number PS221937. If this does not help, try using a hammer. With one hand, hold your screwdriver in place and slowly try to turn it while hitting the back of the screwdriver with a hammer. We hope this information is useful!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.