
DISPENSER LIGHT
$
15.89
In Stock



Get this part fast! Average delivery time for in-stock parts via standard shipping: 1.8 days.
PartSelect Number PS16554837
Manufacturer Part Number WR01X37886
Manufactured by
GE
You May Also Need?
Product Description
DISPENSER LIGHT Specifications
This twelve volt dispenser light bulb is a little under two inches long.

How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part fixes the following symptoms:
Light not working | Not dispensing water
This part works with the following products:
Refrigerator.
This part works with the following products:
General Electric, Hotpoint.
Part# WR01X37886 replaces these:
WR01X37885, WR02X10675, WR02X12208
Questions and Answers
Be the first to ask our experts a question about this part!
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Part Videos
Replacing your General Electric Refrigerator DISPENSER LIGHT

Customer Repair Stories
Average Repair Rating: 4.6 / 5.0, 16 reviews.
What's this?
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Solenoid had become rusted/crank door wouldn't close
First, had to use punch tool to pop out electronic face panel. Face unit still connnect via wires. Use painters tape to hold against refrig. Next, Remove ice/water dispenser and also tape to door. This will give you access to solenoid. Remove the 3 screws holding it in place and unplug fsolenoid from Face Panel. Screw new solenoid and place and connnect to Panel. Goood idea is to unplug regrig. while doing this and put a little WD-30 on shaft of solenoid. May want to order new screws, could be rusty, that hold solenoid in place. Sounds a bit complicated but not that bad a job. You'll save over$100 over GE's service.
Other Parts Used:
-
William M from Ft Myers, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
30 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light replacement in dispenser
kick plate replacement at the base of refrigerator. Very easy to replace. No rocket science needed :)
Other Parts Used:
-
Dennis from Frenchburg, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
18 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken dispenser engager
-
joseph from HAMPTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
16 of 37 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drive cup broke, light went out
Just had to pull ice maker drawer out and replace the drive cup which was very simple. Light bulb on door dispenser was kind of hard to get back in cause it is such a small space to screw the bulb in.
Other Parts Used:
-
Stella from Puyallup, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
plastic from auger [front] had broken
removed the depenser or ice collecter disassyble,replace the new auger and install the collecter tray in freezer.the bulbs i got was for use as i needed,at a later date i have not been able to fine the ice and water depenser bulbs on the open market.
Other Parts Used:
-
noah l. from crestview, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
12 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Frost In Frezer Compartment Where Chute Meets Ice Cube Maker
Removed front panel (using small screw driver) by popping it out, disconnected wire from solenoid, removed solenoid which was rusted, 3 small philip head screws held it in place insereted new solenoid,connected wire snapped front panel back in. Clapper valve closes tightly and no frost in frezzer, saved my self a bunch of money.
Other Parts Used:
-
Anthony from Miramar Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light burned out
unscrewed lamp and replaced it with new one!
-
Gerald from Lincoln, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
10 of 22 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice door light bulbs burned out
found the correct bulbs, the hardest part.
un screwed old bulb.
Screwed in new bulb.
Waa La,
There was light.
un screwed old bulb.
Screwed in new bulb.
Waa La,
There was light.
-
Austin from New Portland, ME
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
7 of 14 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice dispenser light wouldn't light
remove old bulb by screwing it out/install new bulb by screwing it in.
-
Paul from Damascus, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Filter and Light Dispenser replacement
My water filter was a breeze to install. Just push up and to the right and it locks right in.
As for the Water Dispenser light. Just screw it in!!
As for the Water Dispenser light. Just screw it in!!
Other Parts Used:
-
dan from columbus, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer Reviews
Filter By Rating:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Debra G - October 2, 2022

Pro and con
Purchased this tiny light bulb, which worked fine....but shipping price for this item was outrageous.
Lewis H - February 23, 2021

Missing Bulb
We had without the bulb for so long, couldn't find a replacement anywhere before I found your site.
Wish I could have found you earlier
Elizabeth E - June 10, 2020

Works very good
Bulb works very good, very happy to find the right part. Part shipped quickly.
Richard W - November 19, 2019

Perfect part
Just a special size light bulb.
Ron B - July 29, 2019

Easy repair
3 min repair, great
Jose S - April 24, 2019

No issues the correct item arrived.
The correct item arrived and worked perfectly.
Byron L - February 6, 2019

Refridgerator exterior light bulb
Arrived quickly. Works perfectly!
Russell E W - November 27, 2018

GE Refrigerator Door Bulb
This worked great. I purchased two on other sites which did not work. Only buy GE certified parts.
JEFF G - November 1, 2018

Great part
Great part, fast ship
Kenneth M - November 1, 2018

Hard to find but worth its weight in gold
This part is the only one that works. Other bulbs will not work and GE was out of stock.
Model Cross Reference
This part works with the following models:
PartSelect Number: PS16554837
Manufacturer Part Number: WR01X37886
Manufacturer Part Number: WR01X37886
Brand
Model Number
Description
