Quick Question!

Have you ever purchased from PartSelect.com before?

11744233-1-S-Whirlpool-WP74008369-Oven Sensor
11744233-1-S-Whirlpool-WP74008369-Oven Sensor https://www.partselect.com/Schematics/Maytag/55330.gif

Oven Sensor

Your Price

$62.67
Order within the next 10 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11744233
Manufacturer Part Number WP74008369
Manufactured by Whirlpool

This sensor detects the temperature within the oven cavity.

This part works with the following brands: Whirlpool, Jenn-Air, KitchenAid, Maytag.

This part works with the following products: Wall Oven, Microwave Oven Combo.

This part fixes the following symptoms:

  • Little to no heat when baking.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Most Recent

Question:

Getting "function not available" and error code 1d11. What is this telling me?

David for model number JJW8530DDB
Answer:

Hello David, thank you for your question. Error code 1d11 indicates that there is a runaway temperature while the door in unlocked, meaning that the temperature sensor is getting a reading of over 600 degrees. If you are getting this error while the oven is cool that indicates your temperature sensor might be faulty, or the connection is loose. If the connection is fine the sensor's resistance can be tested with a multi-meter. At room temperature it should read 1070 ohms. If the sensor is fine there might be an issue with the control board, you can try a reset by unplugging or shutting off the breaker to the appliance and then restoring power. If that does not help the control board may need to be replaced. I hope this helps, best of luck with your repair!

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.2 / 5.0, 3 reviews What's this?
1-3 of 3
 

7 of 8 people found this instruction helpful

Parts Used:
  • Oven Sensor
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Nutdriver, Pliers
Customer: Alan from Wallkill, NY

Oven temp wrong

Remove the oven door. Remove 3 self tappers on rear wall of oven to take off a round access panel. Pull out a pre-cut rectangle of insulation. Next I removed the 2 screws holding the sensor in place. Pulling the sensor out a bit told me I was "touching" the correct wires in the SMALL rectangular opening. The wires are not visable and 2 hands do not fit in this small opening.I looked at the NEW sensor to see the release on the sensor plug. Slip the angled needle nose into the opening and grasp the plug/release side. The plug pulled apart easily. The sensor wire pulls out with a little bit of twisting to fit it out the hole. The new plug pushes in and has to be worked down to where you can reach it. The same angled plier works to re-attach it. It takes longer to read this than to do the job. Best of luck, Al

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Oven Sensor
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set, Wrench set
Customer: dan from Gallatin, TN

Oven had error messages

I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
  • Oven Sensor
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: patrick from Colleyville, TX

Sensor went out after fire in oven fault code 1b11

I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11744233
Manufacturer Part Number: WP74008369
Brand Model Number Description
Jenn-AirJJW8527DDBWall Oven
Jenn-AirJJW8527DDQWall Oven
Jenn-AirJJW8527DDSWall Oven
Jenn-AirJJW8527DDWWall Oven
Jenn-AirJJW8530DDBWall Oven
Jenn-AirJJW8530DDQWall Oven
Jenn-AirJJW8530DDSWall Oven
Jenn-AirJJW8530DDWWall Oven
Jenn-AirJJW8627DDBWall Oven
Jenn-AirJJW8627DDQWall Oven
Jenn-AirJJW8627DDSWall Oven
Jenn-AirJJW8627DDWWall Oven
Jenn-AirJJW8630DDBWall Oven
Jenn-AirJJW8630DDQWall Oven
Jenn-AirJJW8630DDSWall Oven
Jenn-AirJJW8630DDWWall Oven
Jenn-AirJJW9527DDBWall Oven
Jenn-AirJJW9527DDSWall Oven
Jenn-AirJJW9527DDWWall Oven
Jenn-AirJJW9530DDBWall Oven
Jenn-AirJJW9530DDPWall Oven
Jenn-AirJJW9530DDSWall Oven
Jenn-AirJJW9530DDWWall Oven
Jenn-AirJJW9627DDBWall Oven
Jenn-AirJJW9627DDSWall Oven
Jenn-AirJJW9627DDWWall Oven
Jenn-AirJJW9630DDBWall Oven
Jenn-AirJJW9630DDSWall Oven
Jenn-AirJJW9630DDWWall Oven
Jenn-AirJJW9827DDBWall Oven