This part fits inside the metal shroud or housing.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Dryer.
This part works with the following products:
KitchenAid.
Part# WP697663 replaces these:
AP6010625, 697663
Customer Repair Stories
Average Repair Rating: 4.1 / 5.0, 3 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Clothes were coming out damp.
UNPLUG THE DRYER FIRST I had increased the temp,but the clothes still came out a little less damp so I felt it was the Element. To replace it,take the back off.Just 5 screws,with the back off there is a long metal shield on the right side which contains the element.a single screw at the bottom of the shield has to be taken out.it is in f
... Read morerom the back of the shield.a 5/16 open end wrench is what I used.with the screw removed just remove the 2 wires at the bottom and slide the element out then insert the new element.I did not use the screw that was in there I found it was easier to use number6 screw,nut,and lock washer.Put the 2 wires back and plug the unit in.
Read less
Robert from Elkton, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
2 of 6 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My drying element had to be replaced
Check that nothing else is broken. If you're replacing the drying element, chances are the thermocouple is broken, too. Also, replace your dryer vent with the new metallic, fire resistant one. The old one is probably clogged anyway. Now, to replace the element simply place the dryer on its front and take off the back panel (you only need
... Read morea screwdriver). The heating element is at the lower right, if your standing behind the machine. It's in a metal shroud. Take off the leads, which are outside the shroud. Remove the 5/16 hex-screw (if you can get a socket in, great. I could not. You can also use a slotted offset screwdriver.) The head is inside the shroud and the tip points out toward you. Now, wrestle out the heating element. It's a tight fit, but a little pull and it should come out. Put the new one back in the same way, and again it may take a little wrestling. Now just replace the hex screw and the leads, put the back cover back on and flip it back up. You should have heat very quickly. I could do this repair a second time in about 15 minutes.
Read less
Joe from Los Gatos, CA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench set
18 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Clothes Not Drying Good
Cut power off , till over dryer, take bsce cover off, remove screw fron heating element pull out, vac all dirt up put new one in replace cover cut power bace on
RONALD W from CARSON, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
6 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Phuoc
December 27, 2017
How do I remove the heating element
For model number KEYE760WWH1
Hi Phuoc,
Thank you for your question. Here is a video that will show you how to access your element to replace: https://www.youtube.com/watch?v=GtSdiY8S-Q8&t=52s . Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Craig
February 19, 2018
How do i remove the heating element from the metal shroud or casing.
For model number KEYE660WWH0
Hi Craig, Thank you for the question. Here is a repair story left by a previous customer. "Take off the leads, which are outside the shroud. Remove the 5/16 hex-screw (if you can get a socket in, great. I could not. You can also use a slotted offset screwdriver.) The head is inside the shroud and the tip points out toward you. Now, wrestle out the heating element. It's a tight fit, but a little pull and it should come out" Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.