Maytag/Maytag_Thumb/31220.gif
See part 12 in the diagram
( Grid squares measure 1x1 inch )

Get in touch, we're here to help!

Open until 10PM EST

customerservice@partselect.com

Single Felt Pad

★★★★★
★★★★★
1 Review
$ 4.86   In Stock

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11742772
Manufacturer Part Number WP500092
Manufactured by Whirlpool
Product Description

Single Felt Pad Specifications

This pad is used for many clothes dryers. It is made of a felt material and it is a little over an inch long.

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Noisy | Will not tumble
This part works with the following products:
Dryer.
This part works with the following products:
Amana, Maytag, Speed Queen.
Part# WP500092 replaces these:
AP6009604, 5-0092, 500092
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Roger
    January 21, 2020
    Does this pad stick to bracket or drum glides ? Or does it matter ?
    For model number ps11742772
    Hello Roger, Thank you for the question. These pads stick to the brackets. We hope this helps.

    1 person found this helpful.

    Was this helpful?
    Thank you for voting!
      Customer Repair Stories
       Average Repair Rating: 3.3 / 5.0, 11 reviews. What's this?
      Sort by:
      Sorry, we couldn't find any existing installation instruction that matched.
      Noisy - Clothes getting stuck between drum and bulkhead
      1) Removed lower panel
      2) Removed door
      3) Removed Front Panel - removed connectors from switch and marked connections
      4) Removed Front Bulkhead
      5) Glides and Felt pads were missing, and brackets were nearly worn through
      6) Removed and Replaced old brackets
      7) Attached self-adhesive felt pads
      8) Attached Drum Glides
      9) Removed old felt seal
      10) Glued new felt seal in place with 5-min epoxy
      11) Allowed Epoxy to set and stop stinking
      12) Re-attached front bulkhead
      13) Re-attached remaining parts

      Dryer works great, is quiet again, and no longer eats clothes!!!!!!
      80 of 92 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Dryer made marks, then noise, then more noise
      Thanks to this website we were able to not only find the parts, but a video that told us how to take the dryer apart. Unfortunately, between the time we diagnosed the problem, ordered the parts, and they arrived, the drum had worn into the front bulkhead. We were able to file the sharp parts dull and install the brackets, felt pads, and drum glides along with the felt seal, but ended up breaking the dryer door switch. Once that came in, it has been working. I'm not sure how long the repair will last, but it was much better than buying a new one.
      18 of 501 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      lots of noises
      disassembled found bunch of worn out parts . I went to website wich was very helpful found all . my worn out parts online. dryer is very quiet now I wish i would have done it sooner.P.S. going to fix my dads dryer next. thank you
      18 of 644 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Felt pad on cylinder glide bracket came off.
      First, leaned dryer back and removed 2 screws at bottom front panel.
      Then removed 2 screws at bottom of door assembly.
      Pulled bottom door assembly forward and down.
      Disconnected "can't go wrong" wiring connectors.
      Then removed old cylinder glide rivets at bottom of cylinder using drill motor with 1/4" drill.
      I installed new felt pads on new cylinder glides. Then installed glides with rivet gun.
      Reconnected wire harness.
      Installed door assembly and lower panel assembly.
      BACK IN BUSINESS! THANK YOU!!!!!!!!!!
      8 of 12 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Cylinder glide brackets broke, cylinder seal damage
      After removing the front of the dryer, I took out the front assembly where the seal and glide brackets attatch. I replaced the bad cylinder glide by drilling the old rivets out and re-riveting the new glide in place from the back side. I then replaced the felt pads and glides on the glide brackets and glued a new cylinder seal around the front assembly. I reccomend having 4 hands for placing the cylinder seal around the assembly with fresh glue.
      7 of 9 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      the glide bracket had been warn nearly in half
      1. I removed the lower front panel.
      2. Carful remove the front door making not of which wires whent were of the switch
      3. Removed the front bulkhead.
      4. Drilled out the rivits that held the bracket in place.
      5 Use a pop rivit gun and 1/8 in pop rivit and washer.
      6 Installed the felt pad and the drum guide.
      7 Put the whole thing back together.

      I love your web site the exploded diagrams make fixing my dryer quite easy. I do it. so for under $50 my dryer is almost like new.
      • Rita from brewster, WA
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Socket set
      7 of 8 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      the brackets that support the front side of the tub were worn out and one of them was worn in two
      I started at the bottom and removed the two nut screws that support the bottom section of the front of the dryer. Then I removed the two nut screws that supports the next section and disconnected the two wires ( making note of wich terminals each wire went to). Then I removed the lint trap housing( three phillips head screws hold it in place from the inside). Next ,I removed the face plate( held in place by 4 nut screws and two metal tabs at the bottom). Then I took the old tub brackets and felt seal off of the face plate . Next ,spray adheisive arond the ring of the face plate and install the new felt seal, then the new brackets and dryer glides and felt pads. Last, re-install all components.
      2 of 3 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      worn out bushing in support roller, dryer glides and felt disinigrated. worn out felt cylinder seal
      Unscrew front, detach electrical, tilt back top, remove drum. remove retaining ring and glide, replace ring and guide remove old felt seal, adhere new felt seal with contact cement, remove what was left of felt pads, replace pads and new glides, reassemble.
      2 of 6 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Noisy Belt/Slipping Intermittantly
      Unplug dryer. Remove lower and upper front panels [remove wires from upper right door switch]. Lift up on belt idle pulley and take belt off pulley/motor. Remove front bulkhead and dryer lint/vent ducting. Note position on drum and remove belt. Unbolt top panel front 2 screws to allow room to remove drum. Remove drum. Take lock rings off drum support rollers and remove old rollers. Clean roller shafts and apply hi-temp grease [I used ultra hi temp brake grease-ceramic based-small packet can be purchase fm auto parts store]. Re-install new support rollers and lock rings. Re-install drum and slide belt back into position. Remove and replace felt pads and glides into inside of front bulkhead. Reinstall front bulkhead and top panel [connect door switch wires]. Install belt around idle tension pulley. Re-install lower panel. All parts fit perfectly and delivered quickly. Belt had just been replaced previously.
      1 person found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Felt seal was shredded and glide bracket was worn through
      The on-line video showed the dryer top being loosened from the front as the first step. On our dryer, the bottom panel in the front needed to be removed first - two screws, then the front panel(with door)- two more screws and two wires for the switch. Next was the front guide panel - four screws. The glide brackets bolted to this panel and the felt seal was glued to it. Reverse the process to put it all together, and my wife was happy again.
      1 of 2 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Customer Reviews
      Average Rating:
      ★★★★★
      ★★★★★
      1 Review
      3.0
      Filter By Rating:
      • 5 Stars
        0
      • 4 Stars
        0
      • 3 Stars
        1
      • 2 Stars
        0
      • 1 Star
        0
        Sort by:
        Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
          Model Cross Reference
          This part works with the following models:
          PartSelect Number: PS11742772
          Manufacturer Part Number: WP500092
          Brand
          Model Number
          Description
          Amana
          7493-LEM437
          Dryer - DRYER
          Amana
          ALE120RAW
          Dryer - Electric
          Amana
          ALE230RAW
          Dryer - Residential
          Amana
          ALE230RCW
          Dryer - Residential
          Amana
          ALE331RAC
          Dryer - Residential
          Amana
          ALE331RAW
          Dryer - Residential
          Amana
          ALE331RCW
          Dryer - Residential
          Amana
          ALE443RAC
          Dryer - Residential
          Amana
          ALE443RAW
          Dryer - Residential
          Amana
          ALE443RCW
          Dryer - Residential
          Amana
          ALE565SAC
          Dryer - Electric
          Amana
          ALE565SAW
          Dryer - Electric
          Amana
          ALG120RAW
          Dryer - Gas
          Amana
          ALG230RAW
          Dryer - Residential
          Amana
          ALG230RCW
          Dryer - Residential
          Amana
          ALG331RAC
          Dryer - Residential
          Amana
          ALG331RAW
          Dryer - Residential
          Amana
          ALG331RMC
          Dryer - Residential
          Amana
          ALG331RMW
          Dryer - Residential
          Amana
          ALG443RAC
          Dryer
          Amana
          ALG443RAW
          Dryer - Residential
          Amana
          ALG443RCW
          Dryer
          Amana
          ALG565SAC
          Dryer - Gas
          Amana
          ALG565SAW
          Dryer - Gas
          Amana
          DLE330RA-PDLE330RA
          Dryer - DRYER
          Amana
          DLE330RAW
          Dryer - Residential
          Amana
          DLE330RC-PDLE330RC
          Dryer - DRYER
          Amana
          DLE330RCW
          Dryer - Residential
          Amana
          DLG330RAW
          Dryer - Residential
          Amana
          DLG330RCW
          Dryer - Residential

          Get in touch, we're here to help!

          Open until 10PM EST

          Contact Customer Service