11723055-1-M-Whirlpool-W10812421-CNTRL-ELEC
Part Location Diagram of W10812421 Whirlpool CNTRL-ELEC
See part 6 in the diagram
( Grid squares measure 1x1 inch )
11723055-1-S-Whirlpool-W10812421-CNTRL-ELEC 11723055-2-S-Whirlpool-W10812421-CNTRL-ELEC 11723055-3-S-Whirlpool-W10812421-CNTRL-ELEC Part Location Diagram of W10812421 Whirlpool CNTRL-ELEC
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

customerservice@partselect.com

CNTRL-ELEC W10812421

 Fits your WTW8040DW0!
★★★★★
★★★★★
1 Review

Rated by 1 customer 

A Bit Difficult 

More than 2 hours 

Ratings submitted by customers like you who bought this part.

$ 439.22
  On Order
Get FREE EconoShip on orders over $100! T&C apply
♻ $60Recycling Rebate
♻ $60Recycling Rebate
 Fits your WTW8040DW0!
PartSelect Number PS11723055
Manufacturer Part Number W10812421
Manufactured by Whirlpool
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Whirlpool.
Part# W10812421 replaces these:
W10625549
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
1 Review
5.0
Filter By Rating:
  • 5 Stars
    1
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Terry N - October 29, 2018
  Verified Purchase
Part works perfectly.
The part arrived in great shape and in good time. After installation, the machine works perfectly, even better than the original. My wife insists that the water level is right now and wasn't before, even when the machine was new.
  • 1
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.0 / 5.0, 1 reviews. What's this?
Sort by:
  • 1
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
WASHER QUIT WORKING, FULL OF WATER, NO CODES. DETERMINED FROM INTERNET GOOGLE SEARCH THAT CONTROL BOARD WAS BAD.
HAD A HARD TIME FINDING ANY YOU-TUBE VIDEO THAT SHOWS MY EXACT MACHINE. MAYBE BECAUSE IT IS ONLY 3 YEARS OLD. FINALLY FOUND A PARTS DIAGRAM THAT SHOWED LOCATION OF CLIPS TO RELEASE THE CONTROL CONSOLE FROM THE TOP DECK. ONCE I GOT THE CONSOLE FREE, IT WAS ONLY A FEW MINUTES TO REPLACE THE BOARD AND CONNECT BACK UP. MY MACHINE HAS NO KNOBS ON THE FACE SO I COULDN'T USE THE "STANDARD" CALIBRATION TECHNIQUE. INSTRUCTIONS WITH NEW PART SAYS THAT RUNNING IN "CLEANING MODE" WILL CALIBRATE. i TRIED THAT BUT HAD TO QUIT AS WATER WAS LEAKING FROM THE BOTTOM OF MACHINE. THE NEXT DAY, I BAILED AT LEAST 40 GALLONS OF WATER OUT SO I COULD MOVE THE MACHINE OUT TO LOOK FOR THE LEAK. WHEN I REMOVED THE BACK AND TRIED THE MACHINE, I GOT AND F1, E3 ERROR CODE. SINCE I HAD THE WATER SHUT OFF, I FIGURED THIS WAS THE PROBLEM. BUT MACHINE WOULD ONLY PUMP THE REST OF THE WATER OUT, FLASH THE E3,F1 CODE OVER AND OVER. FOUND A YOU-TUBE VIDEO COVERING A MAYTAG WASHER WITH THE SAME SYMPTOMS. SIMPLE FIX WAS TO REMOVE THE AIR TUBE FROM THE CONTROL BOARD, BLOW INTO IT TO REMOVE ANY OBSTRUCTIONS AND WATER, RECONNECT AND DONE. SURELY THIS WOULD BE TOO SIMPLE BUT WHEN I PLUGGED THE MACHINE IN AGAIN AND HIT THE POWER BUTTON, EVERYTHING LIT UP LIKE IT SHOULD. I WENT BACK TO THE UTILITY SETTING FOR CLEANING THE WASHER. THIS TIME, NO WATER LEAKS AND EVERYTHING WORKED FOR THE 1 HOUR PLUS CLEANING CYCLE. I NEVER DID FIND ANYTHING LEAKING IN THE BACK OR UNDER THE TUB. I PUT ALL BACK TOGETHER AND MACHINE WORKS LIKE A DREAM.
REMEMBER- CONSOLE CLIPS ARE ON THE FRONT CORNERS OF CONTROL CONSOLE AND REQUIRE A FLAT THIN AND NARROW BLADE TO RELEASE THEM, SUCH AS A TABLE KNIFE. THERE ARE 2 SCREWS TO REMOVE FROM THE BACK PANEL THAT ARE INTO THE PLASTIC CONSOLE. REPLACEMENT SHOULD BE A 10 MINUTE JOB IF YOU COULD GET INSTRUCTIONS.
Read less
  • Terry from BLOOMFIELD, NM
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Back to Top
Questions and Answers

Be the first to ask our experts a question about this part!

Back to Top
You May Also Need ?
Produce Preserver Filter
$21.56
$21.56
  In Stock
Affresh Washing Machine Cleaner - 3 pack
$12.60
$12.60
  In Stock
Affresh Dishwasher Cleaner Tablets - 6
$19.10
$19.10
  In Stock
Affresh Cleaner
$19.10
$19.10
  In Stock
Cooktop Cleaner
$17.76
$17.76
  In Stock
Affresh Ice Machine Cleaner
$20.52
$20.52
  In Stock
Back to Top
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11723055
Manufacturer Part Number: W10812421
Brand
Model Number
Description
Whirlpool
WTW8000DW0
Washer - WASHER
Whirlpool
WTW8000DW2
Washer - RESIDENTIAL
Whirlpool
WTW8040DW0
Washer - WASHER
Whirlpool
WTW8040DW2
Washer - WASHER
Back to Top
Customer Service Representative

Get in touch, we're here to help!

Daily 8am - 9pm EST

Contact Customer Service
CNTRL-ELEC
$ 439.22
  On Order
✖
Stock Status
 In Stock

Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.

If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.

 On Order

Item is not in stock and usually ships 3-5 business days from the time you place your order.

 Special Order

Item is not in stock and usually ships 10-15 business days from the time you place your order.

 NLA - No Longer Available

This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.