Temperature Sensor WB21X22134 | Official GE Part | Fast Shipping | PartSelect
Quick Question!

Have you ever purchased from PartSelect.com before?

Temperature Sensor – Part Number: WB21X22134
Temperature Sensor – Part Number: WB21X22134 https://partselectcom.azureedge.net/Schematics/GE/00115410i02.gif

Temperature Sensor

14 Reviews
Your Price
$13.39

Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS10059162

Manufacturer Part Number WB21X22134

Manufactured by GE

The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. Before you make this repair remember to unplug your range from the power source, and turn off the gas shut off valve.

This part works with the following brands: General Electric, Kenmore, Hotpoint

This part works with the following products: Range, Wall Oven, Microwave Oven Combo

This part fixes the following symptoms: Little to no heat when baking | Oven not heating evenly | Oven is too hot | Will Not Start

Questions & Answers

Most Helpful

Question:

When turning the oven on it starts to warm and then a code f2 appears and oven shuts off

Stephen for model number Jb650dt1ww
July 20, 2017
Answer:

Hi Stephen, thank you for your question. If your oven is not warming, the oven temperature sensor is likely the problem, and replacing it with this part will solve that. The F2 code means there is a problem with the temperature. If you'd like to do more research before buying a replacement sensor, you can test the sensor with a multimeter (make sure the range is at room temperature, unplugged, and disconnect the sensor first). The sensor should read about 1100 ohms, if it is off, replace the sensor with this part. I hope this helps with your repair!

11 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Oven starts warming and gets to about 250 degrees and temp stops climbing (set to 350 degrees). Is it the element or the temperature sensor that may be bad?

Chris for model number J2B918SEK3SS
August 11, 2017
Answer:

Hi Chris, Thank you for the question. If the oven is not reaching the set temperature but the element is still getting hot, you will need to replace the temperature sensor. Hope this helps!

7 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

After installing new element. Oven gets to temperature but new bake element overheats and does not shut down

James for model number JBP24WOK1WW
September 7, 2017
Answer:

Hello James, thank you for contacting us. If the oven temps are not consistent then it could be the temperature sensor sending bad readings to the control board. You can test this with a multi-meter. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If you get a reading that is far off from that, you will need to replace the sensor. Hope this helps!

3 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My electric oven does not heat to the set temperature. I set temperature pre heat to 350 degrees. Display on stove control panel will show 350 degrees after pre heat but the thermometer that I placed inside the oven only reads about 225 degrees.Then I let the oven cool off and set the preheat to 250 degrees display show 250 degrees after preheat but the thermometer that was placed inside oven did not rise at all. Object got warm but I could reach in with bare hand and take it out. Guess I have a problem. What might it be?

Betty for model number JBS55DM2WW
March 30, 2018
Answer:

Hi Betty, Thank you for the question. This sounds like an issue with the Temperature Sensor, PartSelect Number: PS10059162.The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor.Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. Hope this helps!

3 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My oven is taking 25 minutes to reheat to the standard 350 degrees. It used to take only about 10 minutes. What part might i need?

Myra for model number JB620DR1BB
April 24, 2018
Answer:

Hello Myra, thank you for your question. The most likely issue is the temperature sensor, part number WB21X22134. The function of the oven temperature sensor assembly is to measure the temperature inside your oven while it is on and send the temperature back up to the electronic control, which adjusts as necessary. If your oven is having difficulty achieving warmer temperatures and/or keeping warmer temperatures up, you may want to test your temperature sensor. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If the sensor is tested and is working okay, the the issue is likely with the electronic control board. I hope this helps. Thank you and have a great day!

3 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Read all questions & no one seemed to have this problem. Oven has been cooking food for some time; i press on & + on burner; display blinks a few times then shuts off - oven also shuts down. Nothing will restart, burners or oven. Burners are induction and despite having the proper pan it is not making a connection. An appliance clerk said it sounds like the sensor or mother board. Am i suppose to be seeing error codes? There are none.You cover the sensor testing but i didn't find how to test the board. Can you tell me and what is your idea on this? Thanks

Ronnie for model number PHS920SF2SS
February 27, 2018
Answer:

Hi Ronnie, Thank you for the question. Only way to test the board is to see if it had 240 Vac going to it, if there is and it is not working properly and the sensor is good, then the board will need to be replaced. You will not always get error codes when they are defective. Hope this helps!

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

I wrote -read all questions & no one seemed to have this problem. Oven has been cooking food for some time; i press on & + on burner; display blinks a few times then shuts off - oven also shuts down. Nothing will restart, burners or oven. Burners are induction and despite having the proper pan it is not making a connection. An appliance clerk said it sounds like the sensor or mother board. Am i suppose to be seeing error codes? There are none.You cover the sensor testing but i didn't find how to test the board. Can you tell me and what is your idea on this? Thanks Ronnie for model number phs920sf2ss You answered but forgot to tell you this has happened 3 times so far and every time the range and oven will work after several hours. Range does not seem to be the problem unless we have the oven on. Does this still make it probably the sensor or board. Sorry to bother you again....... i'm a woman with a long forgetory.

Ronnie for model number phs920sf2ss
February 28, 2018
Answer:

Hi Ronnie, Thank you for your question. If the oven is not heating correctly, then the issue is likely with the oven sensor and you will need to check it with a multimeter. When testing the sensor with a multimeter, the sensor should be tested at room temperature. You will need to measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. If the sensor is working okay, the the issue is likely with the electronic control board. I hope this helps. Thank you and have a great day!

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My oven starts out fine but doesn't maintain heat. Best to replace the sensor or both sensor and heating element?

Dawn for model number JB700DN2WW
November 20, 2017
Answer:

Hi Dawn, Thank you for your question. I would actually suggest testing both your element and your temperature sensor first to see which part is malfunctioning. You can test both of those parts with a multi meter. If they are both testing in working condition, then it may be your electronic control board that is the issue. I hope that helps. Good luck with your repair.

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Hello my oven works when on broil but wont for bake took element had it tested it was fine also my oven light will only work when its on broil otherwise it goes out? How do i test the temperature sensor? Does it sound like thats the problem?

SHAUN for model number jks06g003b
December 23, 2017
Answer:

Hello Shaun, Thank you for your inquiry. You can test the part with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!

2 people found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Oven won't turn on. Worked last time used

Fred for model number JGS905SEK2SS
September 18, 2017
Answer:

Hi Fred, Thank you for your question. There are a number of parts you may want to check. I would suggest checking your oven sensor and your ignitor. If both of those parts are fine, you may have to look into your electronic control board. I hope that helps. Good luck.

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My GE profile gas oven will not come on.The top burners and the broiler work. Not the oven.When I set the temperature to 400 on bake, the temperature on the led readout automatically goes to 100 degrees and will not move from that point. I have shut off the power and attempted to restart with no luck.Same symptom.Temp. Reading 100 with no heat at all coming form the oven..any ideas?

Michael for model number JGS968Kek3CC
October 31, 2017
Answer:

Hi Michael, Thank you for the question. This normally indicates there is an issue with the Temperature Sensor and it will need to be replaced. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Oven does not shut off at temp set - temperature will rise well past set temperature

Scott for model number ra624f1wh
January 17, 2018
Answer:

Hi Scott, Thank you for the question. Sounds like the sensing probe on the Thermostat is defective. I suggest replacing the thermostat and prob, PartSelect Number PS773933. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

My oven is throwing an f3 code. How do I get to the temperature sensor to replace it manually

Brittany for model number JBP23DR1WW
February 12, 2018
Answer:

Hi Brittany, Thank you for the question. The temperature sensor, also known as the oven temperature sensor assembly is usually found in the back of the oven. You will need to remove the back panel to access the plug for the sensor. Hope this helps!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

On "bake" as opposed to "convection" the oven will show the set temperature on the display but maintain a constant temperature 30 - 40 degrees cooler. So say if set at 350 degrees it will indicate that it has come to temp. I wai a few minutes and then shut it off and restart it and it will say say its only at 318 and will kick on to raise the temp. We have tried different temps and it consistently does the same thing. We have tried baking things (potatoes) and they take a lot longer than normal. Also tried an independent t-stat in the oven.

Don for model number ge profile oven
4 days ago
Answer:

Hello Don, thank you for your question. The most likely cause of this heating issue is the oven temperature sensor. This is the part that senses the internal temperature. It could also be an oven control board issue. There are ways to test the sensor. Please feel free to resubmit the question with the model number of the appliance and we will be happy to help you find the correct part number and testing information. Look forward to hearing from you!

1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer

Most Recent

Question:

I shorted the oven light fixture thinking the two screws over the glass cover was a bezel that released the glass. Didn't think i needed to disconnect power to replace a light bulb. Foolish i know but mis-read the assy & expected to exchange the oven bulb. Anyway, whole control panel wb27t11487 is out and oven not working. Is anything protecting the control panel otherwise? All burners work. There was no electrical odor at the time. Just an instant zap & loss of all red control panel digital lights. I do not see any burn spots on control panel or anywhere else.

Marshall for model number JB650DF1BB
Yesterday
Answer:

Hello Marshall, thank you for your question. It sounds like the oven control board Part Number: PS8767124 was fried. We would recommend replacing that part. I hope this helps.

Was this helpful?
Show Answer
Hide Answer
Question:

This is a continuation of my question yesterday. The model number is attached. I didn't mention that we have replaced the entire control board as recommended by an appliance repairman. Nothing improved, he seems at a loss and told us to keep using it and maybe it would "even out". It hasn't. We got into the "special features" section of the controls which allowed us to raise the temp in the oven 30 degrees but it just seemed way too hot and burned things so we put it back where it was. So seems like the temp sensor is the next logical choice. I'm fairly handy so changing it myself is not a problem.

Don for model number GE Profile P2S920SEF4SS
2 days ago
Answer:

Hello Don, thank you for your question. The most common cause of any heating issue ( not heating evenly, oven getting too hot, not reaching temp, or fluctuating temp) is caused by the temperature sensor PartSelect Number: PS236490. When testing the sensor with a multimeter, the sensor should be tested at room temperature. You will need to measure the resistance between the two prongs at the end of the sensor connector. Replace the oven sensor if the reading is less than 900 Ohms or more than 1200 Ohms. I hope this helps!

Related Parts: Temperature Sensor Kit
1 person found this helpful.
Was this helpful?
Show Answer
Hide Answer
Question:

Oven not coming up to temperature .. example set to 450 goes to 385... however when restarted shows 310... element has been replaced in the last 6mos and has brand new relay board .. any help would be appreciated..,thanks

Paul for model number LG electric stove 2011
November 15, 2018
Answer:

Hello Paul, thank you for your question. There are two parts that could be causing this issue. The sensor and the main board. Most likely, the sensor is bad and needs to be replaced. If you could provide the model number of the LG appliance, we can provide the part number, price and testing information!

Was this helpful?
Show Answer
Hide Answer
Question:

Stove top works fine. When oven is turned on with the stove top also being on the breaker trips. It doesn't trip until the oven is approx 300+ degrees

Richard for model number jbs55dm2ww
November 14, 2018
Answer:

Hello Richard, thank you for your question. The most likely issue is the oven sensor. We would recommend testing the sensor with an ohm meter. You should get a reading of about 1080 ohms when testing this part. If you get a reading much higher, or lower than this the sensor needs to be replaced. If the sensor is tested and reads very close to 1080 ohms, the board is the problem and would have to be replaced. I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

My stove is showing f4 code? And my oven stopped working?

Carmen for model number JGB635DEK1BB
November 14, 2018
Answer:

Hello Carmen, thank you for your question. The most likely issue is the oven sensor. We would recommend testing the sensor with an ohm meter. You should get a reading of about 1080 ohms when testing this part. If you get a reading much higher, or lower than this the sensor needs to be replaced. If the sensor is tested and reads very close to 1080 ohms, the board is the problem and would have to be replaced. I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

I'm getting an f96 code when the over starts heating

Keith for model number ptf550dfbb
April 26, 2018
Answer:

Hello Keith, thank you for your question. The F9 code on GE ovens indicate that the units electronic control system detected an issue with the door lock mechanism. I would recommend testing the thermostat just to be safe. To test the sensor, use an ohm meter to check for resistance. The sensor should read between 1000 and 1100. If the sensor is working properly, and tests within those ranges the sensor is not faulty and the door lock, which is part number WB10X28391, should be replaced. I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

Lost power when power came back on. Clock works but stove top not working and oven not working. Turned circuit breaker off and on but did not change anything

Michael for model number JBS55DM5BB
April 3, 2018
Answer:

Hi Michael, Thank you for your question. There are a few parts that you should check. First I would suggest checking your wiring harness and your terminal block where your power cord connects to the appliance. If all of your wires are fine, it might be your burner switches and actual control board that are the problem. Even if the clock portion of your board is working, the other components that control your oven might have overloaded. i hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

Per your suggestion i replaced the temperature sensor in my oven. However, the oven still does not work. The indicator remains on preheat while the oven never reaches the desired temperature. I also ordered and replaced the bake element in the oven less than a year ago. Please advise as to possible solution.

Dallas for model number JBP22BK4CT
March 26, 2018
Answer:

Hi Dallas, Thank you for your question. There are only a few parts that could cause this sort of issue. It would be your bake element, your temperature sensor, or your electronic control board. If both your bake element and your sensor are fine, then it might be your electronic control board that is the issue. I hope that helps. Good luck with your repair.

Was this helpful?
Show Answer
Hide Answer
Question:

The oven will come on and stay on for indeterminate time. Sometimes 15 minutes and i get the f2 error. Sometimes for hours before the error comes on. But it never heats up to the right temp. I tried adjusting the temperature. The sensor is running 1148 ohms. Any suggestions?

Mary Thoreson for model number JB650SF1SS
February 25, 2018
Answer:

Hello Mary, Thank you for your inquiry. F2 indicates an error with the temperature. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature-if it does not, then replace it. Also double check the wiring going to the sensor as well as the temperature circuit, check the elements for continuity as well. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

My oven door keeps locking during cooking time, how do i repair this

Rocky for model number Jkp30dp1bb
February 20, 2018
Answer:

Hello Rocky, thank you for your question. If the door lock is engaging during a regular bake or broil setting, I would suggest checking the temperature sensor, the lock mechanism and the electronic control board. I hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

The oven was heating up then the next time we tried the elements won't heat up for bake or broil. This is a combo unit (microwave and stove).

jayre reaves for model number JKP86S0H6SS
January 2, 2018
Answer:

Hello Jayre, Thank you for your inquiry. We would recommend checking the following parts to fix your issue: the bake and broil elements, the fuses, the thermostats, the temperature sensor, and the control board. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, there are YouTube videos available to assist you. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

When I set my oven to the desired heat, such as 400 degrees, the number read-out will show the oven is heating, yet when you open the oven, it is not even close to the temperature you selected. Yesterday, I set the oven for 400 degrees yet it was maybe 175-200 degrees in the oven. I put a pizza in it and in 20 minutes the pizza only looked like it was on defrost. Could it possibly be this temperature sensor I read of on your site?

Nancy for model number JB870DT1BB
January 2, 2018
Answer:

Hello Nancy, Thanks for your question. Yes, the temperature sensor is a likely cause for your issue. This part PS10059162 is for the lower oven, while part number PS236398 is for the upper oven. Test the bake element as well with a multi-meter to see if it has continuity and replace it if it does not show continuity. If all else is testing well, consider replacing the convection motor after checking if the fan blade turns properly. I hope this helps.

Was this helpful?
Show Answer
Hide Answer
Question:

I turn on the oven on confection and will not heat up, is this what i need?

Rich for model number JB968SL5SS
December 26, 2017
Answer:

Hello Rich, Thank you for your inquiry. It could be either this part or the convection element itself. You can test those with a multimeter. Hope this helps!

Was this helpful?
Show Answer
Hide Answer
Question:

How difficult is this item to replace?

Dan for model number WB21X22134
December 18, 2017
Answer:

Hi Dan, Thank you for your question. There is a video on our website that you can reference on how to install the temperature sensor. The oven in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS820208. I hope this helps. Thank you and have a great day!

Was this helpful?
Show Answer
Hide Answer

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 19 reviews What's this?
1-15 of 19
89 of 116 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Peter from stamford, CT
Oven would go in to a f2 error
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

37 of 45 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Gerald from Cape Canaveral, FL
Oven wouldn't preheat above 300 degrees
Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

21 of 23 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Customer:
Chad from Bloomington, IN
I kept getting an f2 error and the temperature did not seem accurate
1) pull out the stove
2) remove the 7 sheet metal screws holding the back panel on. (the panel that also covers where the cord splits and connects to the oven.
3) Find the small plastic connector located in the middle of the back of the range and unplug it.
4) open the front of the oven and remove the one screw holding in the oven temp sensor.
5) replace the sensor and make sure to "feed" the new cord through as best you can.
6) I had to dig through the insulation a little bit to find the new wiring harness
7) connect the wiring harness and put the back of the range back on

note: this was very simple to do if you think this might be the problem don't hesitate to handle this one yourself.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

17 of 22 people found these instructions helpful
Parts Used:
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Customer:
Tammy from Emmitsburg, MD
Oven won't get hot, would preheat only -element don't even get hot- only the brioil element got hot.
Repair: unscrewed the back panel- 2 screw and the sensor and bake element from the inside had 2 screws each. Just stuck them through their old hole from inside to the outside, pushed plug back together. Then screwed back into place, screwed back plate back on. Plugged stove in, turned on the oven and within 2 seconds the bake element was blood red and temp. was up to 350 in less then 10 min. Come to find out only needed the oven sensor -$10.00part but I already ordered the bake element so I went a head and replaced it - cost $50.00. Have a great oven again for less then $70.00repair.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 16 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Lee from Greenfield, IN
Oven overheating upto 200 degrees!!
Replaced temperature sensor in the oven first ($10 part, always start with least expensive possibility!), but that didn't solve the problem. 5-10 minute repair, not counting moving the range in and out of it's home between cabinets. Next replaced the control board ($90 part) which solved the overheating problem. 15 to 30 minute repair, don't be intimidated by all the wires. Remember to turn off power at the breaker (duh). Order the faceplate graphic ($37 part) because chances are the old one won't peel off cleanly (ours didn't, "I was really careful Honey!!) and the otherwise excellent PartSelect.com website doesn't suggest the part might be needed. Anyway, I saved a minimum of $80 plus Labor by doing it myself. I had the advantage of living about 100 miles from their warehouse and got NEXT DAY delivery from FedEx instead of 3-5 business days. Suggest you order before noon.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 12 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Socket set
Customer:
Dinah from Juneau, AK
Oven on range did not work properly
My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 8 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Customer:
Roger from MARIETTA, GA
Oven would not heat; temperature sensor failed; needed replacement
Replacing the sensor was a snap and not as involved as I feared. 1) open the oven door; 2) remove the one hex screw holding the old sensor to the back of the oven; 3) gently pull the sensor, pulling the wiring out to access the plastic wire connector (carefully guide the plastic wire connector through the opening); 4) loop a small piece of wire (stiff enough to form a hook) around the base of the wire connector to keep the wire from falling into the back wall of the oven; 5) unclip the connector and remove the bad sensor; 6) clip in the new sensor; 7) remove your catch wire; 8) thread the wiring back through the opening; 9)position the new sensor and secure with the hex screw; and 10) turn on the oven and prove to your wife you do know what you are doing!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 7 people found these instructions helpful
Parts Used:
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Customer:
Stephen from CAPE CHARLES, VA
Stove not heating properly for baking. Since unit is 13 years old, I decided to replace both heating elements and temperature sensor.
Turned off breaker for stove. Pulled stove from wall and turned it to access back. Unplugged cord for better movement of unit. Took off back panel exposing connecting wires and disconnected them all. Unscrewed element and sensor screws using small socket wrench and removed from oven. Replaced three items and rescrewed. Went to rear of stove and reconnected all wiring. Moved stove to plug back in and turned oven on. Everything worked fine so I let the unit cool for 20 min to 1/2 hour. Replaced back panel and pushed stove back in place. Fairly easy repair. DO NOT lean on oven door! Oven will tilt forward with enough pressure.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 11 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Cindy from Murrells Inlet, SC
Oven not holding a consistant temperature. Found the replacement part easily on you website.Thanks to your photo.
First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 7 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Customer:
Mary from Bolton, MA
When inspecting the back of my oven I noticed the cable had been pushed under (my guess from the mouse I found electrocuted where the power lines come in) and was touching one of the element prongs which burned the covering.
Not counting unplugging it and taking off the 3 back panels of the oven (< 5 min.) It took < 2min. to change out. Unclipped cable in back, unscrewed one screw inside of oven at top between the two elements and pulled cable through to front, reversed to attach new sensor. Buttoned up the back, plugged back in and was good to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
emmett from rocky mount, NC
F2 fault code kept appearing on oven
Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Theaded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Customer:
Joseph from LIBERTY HILL, TX
Oven in accurate temp too low.
Open the oven , remove one screw holding the sensor remove the sensor and replace the sensor.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
Glenn from Grapevine, TX
Oven temperature would not go above 240 degrees
Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven temperature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found these instructions helpful
Parts Used:
  • Temperature Sensor
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
Customer:
Diane from BUTLER, PA
Heat sensor malfunction
Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, thats it...

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found these instructions helpful
Parts Used:
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Customer:
BRIAN from NEWARK, DE
Baking element broken
Baking element : Pull range away from wall. Disconnect the power. Remove back center panel. Remove range door. Remove range racks. Disconnect push on terminals fron baking element. Remove two hex head screws. Remove baking element. Reassemble in reverse order..........Temperature sensor: with back panel removed, unclip the electrical connector. Remove one hex head screw. Remove temperature sensor. Install in reverse order.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-15 of 19
Customer Reviews
Average Rating:
14 Reviews
4.9
out of 5
Filter By Rating:
  • 5 Stars
    13
  • 4 Stars
    1
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Stars
    0
Sort by:
Sort by:

Model Cross Reference

This part works with the following models:

PartSelect Number: PS10059162
Manufacturer Part Number: WB21X22134
Brand
Model Number
Description
General Electric
155910
Range
General Electric
15891 1
Range
General Electric
158911
Range
Kenmore
91147619200
Range
Kenmore
91147619201
Wall Oven
Kenmore
91147643100
Wall Oven
Kenmore
91147692100
Microwave Oven Combo
Kenmore
91147699100
Microwave - 27" ELECTRIC BUILT-IN OVEN
Kenmore
91147702200
Wall Oven
Kenmore
91147702201
Wall Oven
Kenmore
91147703200
Wall Oven
Kenmore
91147703201
Wall Oven
Kenmore
91147704200
Wall Oven
Kenmore
91147704201
Wall Oven
Kenmore
91147709200
Wall Oven
Kenmore
91147709201
Wall Oven
Kenmore
91147722200
Range
Kenmore
91147722201
Wall Oven
Kenmore
91147722202
Wall Oven
Kenmore
91147724200
Range
Kenmore
91147724201
Wall Oven
Kenmore
91147724202
Wall Oven
Kenmore
91147729200
Range
Kenmore
91147729201
Wall Oven
Kenmore
91147729202
Wall Oven
Kenmore
91147742200
Wall Oven
Kenmore
91147742201
Wall Oven
Kenmore
91147743200
Wall Oven
Kenmore
91147743201
Wall Oven
Kenmore
91147744200
Wall Oven